FAQ : Which ignition do I have?
 

Question : In the United States, enduro models come equiped as either EC models or DE models. The EC models have larger ignitions and the DE models have smaller ignitions. How can I tell which one is installed in my bike?

Answer : The two ignitions available are the kokusan 2k-2 and the kokusan 2k-3. The 2k-2 is rated to generate 40 watts of power, whereas the kokusan 2k-3 is rated to generate 110 watts of power. In reality they generate about 35 and 85 watts, respectively. Determining which ignition is installed on your bike can be done by simply examining the left side of the engine. The wires for the 2k-2 ignition exit the engine cases at the 10:00 position, whereas the wires for the 2k-3 ignition exit the engine cases at the 2 o'clock position.

Any more I should add here?

For the 2002 and earlier bikes, the XC designation is equivalent to the current DE models in terms of ignitions. In 2003, the EC line was "reintroduced" to the US after the change in distributors from Don Knight (GGNA) to the factory sponsored GGMA.

Here are photos of the different ignitions. 2K-3 is the larger 2K-3 ignition found on Euro ECs. 2K-2post is the smaller 2K-2 ignition found on the DEs and older XCs. In this photo there is a 10oz flywheel weight attached.

Hello,
I buy few time ago cross ignition wlywheel and cdi model2006, the problem is how to instal, because CDI are cross and enduro are same, and when I look for intsal new flywheel, there position are completly different, so I think advance ignition are too much different.
Somebody can explain how to put in the good position, and how many degres before top I must put?
Thank's!!!!

Look at the 2K-2 picture in the Sticky. You will notice a semi-circular cutout in the stator plate form the 12 o'clock position to approximately the 2 o'clock position. In this area, you will see an unused M5 hole in the case (used for the 2K-3) very close to the edge of the cutout. Install a short M5 capscrew and small M5 flat washer. Snug down. Now, rotate the stator plate counter clockwise until it contacts the edge of the washer. Tighten the stator plate M6 bolts. This is where you want to be with the timing.

BTW, so your not confused, for this description "cross ignition" is the 2K-2.

On spare parts book, the reference is: ignition comp MC250534005

"2K-2" and "2K-3" are Kokusan part #s or types, not GasGas #s. The "cross" ignition may even be a 2K-1, which is a 2K-2 with no lighting coil. Same flywheel and stator plate, and the referance I described will work fine to get the bike timed VERY close.

In reality, cross rotor stator is powerless only 40w than 110w for enduro, the weight of cross is:1.146 pounds than 1.984 for enduro, and mesure:3.031inch for cross, and enduro one is the X2.
We talk about exactly the same think but the name is different so your 2k-2 is cross rotor+stator.
I didn't know how to put picture of it, can I send you photographi of it

Thats OK, I don't need a photo. Yes, we are talking about the same thing. I beleive I have answered your question on how to time your bike. Good Luck.

Thank's, but it not answer at all, because as I remenber, when you install light rotor+stator, it look wrong ignition advance, if you look the posittion of the sensor and magnetic, and compare to standart one, it look completly wrong advance.
So if I understood correctly, I have to put stator with sensor down on left, and wire on up left, and it will be approixmatly good.
right?

Install it as the photo shows and how I describe. The wires exit from the front of the cases. Yes, the position of the sensor is different but so is the matching trigger magnet on the flywheel in relation to the crank keyway. It works, trust me.;)

Also, you can use either CDI with either flywheel stator if you like, to experiment with power delivery.

But for model 2005-08, theyr no Cross CDI, all CDI are same, what type of modification you propose on CDI? It look like very interesting!

So what ignition does my MC250 have? Can I get lights setup on it?

Sideshow, Your answere lies in the first post of this thread.

The two ignitions available are the kokusan 2k-2 and the kokusan 2k-3. The 2k-2 is rated to generate 40 watts of power, whereas the kokusan 2k-3 is rated to generate 110 watts of power. In reality they generate about 35 and 85 watts, respectively. Determining which ignition is installed on your bike can be done by simply examining the left side of the engine. The wires for the 2k-2 ignition exit the engine cases at the 10:00 position, whereas the wires for the 2k-3 ignition exit the engine cases at the 2 o'clock position.

Does this hold true for newer bikes? My '08 EC300 exits at the 10 o'clock position = 2k-2. My son's '09 EC250 Racing exits at the 2 o'clock position = 2k-3. Seems a bit backwards to me, of course I'm used to KTM's where the 300's got 3's and the 250's got 2's, that never made much sense to me either.

So are lights easy enough on my bike then? It's a 2k2.

I am hoping to get a tail and a headlight hooked up.

It works well enough for a turkey run/enduro setup.

Oh cool, so I need to just get the wiring setup for it?

I think you need to get a look at the wiring you have. From there you can determine a course of action. You may just have to plug in some wires under the seat and run them to the lights. You may also want to get switches for your brakes.

This may help too:

http://www.gasgasrider.org/gg-wiring.jpg

Awesome. Thanks!

I might just buy the dirtfreak battery powered unit for the purposes of getting a NH road plate and get a good helmet setup if I ever ride at night. Not sure yet, also depends on costs.

The more I look at that chart the more confused I get. It looks like there is a terminal between the CDI and the front headlight?

I'm going to have my bike apart soon to button it up after my crash at the Classic. I'll try to get some better info on the lights. I have the 2k-2, but most of the wires are wrapped so they are not comlpetely visible.

You can't ride at night with this setup, well maybe at 5mph, so you will need a helmet setup if you plan to.

That would be much appreciated.

Voltage regulator. Cheap and you will need one.

Planning on doing a minor tear down and taking some pics so that will help in myh road to lighting.

i know this is probably a dumb question but
i just got ahold of a 98 ec250, cb motor, but its been removed, i have it too.
has what appears to be a 2k2 stator(10 oclock exit) but it exits the case, and had a plastic cover like my 07.
i was given another one with the bike but it is just a coil inside a magnesium cover, it exits this cover at 10 oclock as well..
is there an option of running 2 coils? it fits over everything that is there now. i can build computers, and xboxes, but i cant understand how this is supposed to be..
my 07 had 2k2 stator and it was enuf for my needs