Rieju & GasGas Legacy Riders Club Forum

Rieju & GasGas Legacy Riders Club Forum (http://www.gasgasrider.org/forum/index.php)
-   Enduro Engine - 2 stroke (http://www.gasgasrider.org/forum/forumdisplay.php?f=37)
-   -   2001 XC200 Restoration Project (http://www.gasgasrider.org/forum/showthread.php?t=16363)

Lincolnlock 12-17-2013 04:48 PM

2001 XC200 Restoration Project
 
4 Attachment(s)
So I decided I needed a new project. And why not start with a $400 2001 xc200? The bike needs a ton of work obviously. It didn't start when I bought it, but a couple of new carb jets and it started right up. The bike sounded ok, but after a couple of minute of running the engine shut off and the kick start was really hard to push down. Turns out the lower connecting rod bearing was starting to lock up. Oh well... So I'll post updates as I go. I still need a few more items to put the engine back together. It should be a fun winter project anyway.

bowhunter007 12-17-2013 05:08 PM

Quote:

Originally Posted by Lincolnlock (Post 124495)
So I decided I needed a new project. And why not start with a $400 2001 xc200? The bike needs a ton of work obviously. It didn't start when I bought it, but a couple of new carb jets and it started right up. The bike sounded ok, but after a couple of minute of running the engine shut off and the kick start was really hard to push down. Turns out the lower connecting rod bearing was starting to lock up. Oh well... So I'll post updates as I go. I still need a few more items to put the engine back together. It should be a fun winter project anyway.

I've never ridden a 200cc GG. Should be a fun bike...especially at Walker.

Zman 12-17-2013 05:24 PM

Just did the same thing for my son's 200. While you are in there you may want to consider replacing the other bearings in the trans.

I believe these are the correct transmission bearings but double check against what is in your trans.
Bearing #
Counter shaft bearing 6305C3
Countershaft Seal 30x40x7
Clutch bearing 6205Zc3E
Trans shafts 6203c3
98-02 Crank 63/28c3

pscook 12-17-2013 05:45 PM

Great find! Good thing you found it first.

Quick tips- Crank nut on the water pump side is reverse thread. YZ Flywheel puller is a perfect fit. And Bob Piper at North Tahoe Motorsports will hook you up for all of your hard parts and any tech data you need. Good prices, fast shipping, and good guy. Here's a link to one of his ebay ads- http://www.ebay.com/itm/TOP-END-WOSS...45baf2&vxp=mtr

Drop him a note to see if he has 200 stuff, I would think he should.

Also, the only thing different from the 200 to the 250/300 is machining of the cases, crank, and top end (including jug). The chassis are the same, if you didn't know this already.

Zman 12-17-2013 06:51 PM

Phil - Are you sure about the crank nut being left hand thread? I did a 2002 and a 2004 EC200 recently and I could swear the clutch side crank nut was a traditional right hand thread.

pscook 12-17-2013 09:13 PM

Quote:

Originally Posted by Zman (Post 124511)
Phil - Are you sure about the crank nut being left hand thread? I did a 2002 and a 2004 EC200 recently and I could swear the clutch side crank nut was a traditional right hand thread.

On my 2002 300 it was reverse thread. Lefty tighty and righty loosey. Of course, an initial inspection of the lead-in threads will tell the story, but I am certain that the primary nut is reverse.

Lincolnlock 01-17-2014 04:38 PM

1 Attachment(s)
Well... I got the crank rebuilt with a cr250 rod kit. Then I ordered a truck load of parts. I put the crank bearings in and bolted the cases together. The transmission would only spin a 359 degrees and then lock up solid. So I figured out why the bike was parked. The secondary pinion has a tooth that is about to fall off. So I still need to source another one of those. Other than that gear, the bike would be running again. Oh well. Let me know if there is a used gear I could purchase. This bike project is running over budget. :D

Zman 01-17-2014 06:40 PM

You will not be able to ride it very far that way. ;) That is a bummer.

PEB 01-18-2014 12:20 PM

Sam which gear is the secondary pinion?

Lincolnlock 01-23-2014 02:29 PM

Well, no one in the world seems to have one of these gears. If anyone know of one, please let me know. It is part number: ME25636076


All times are GMT -5. The time now is 10:29 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org