2012 300 Race Pics
3 Attachment(s)
http://www.gasgasrider.org/forum/att...4&d=1327601525
http://www.gasgasrider.org/forum/att...5&d=1327601572 http://www.gasgasrider.org/forum/att...6&d=1327601674 Top: Right side Center: Left side Bottom: Brake pedal mount. Note very strong tab. |
3 Attachment(s)
http://www.gasgasrider.org/forum/att...7&d=1327601944
http://www.gasgasrider.org/forum/att...8&d=1327601987 http://www.gasgasrider.org/forum/att...9&d=1327602050 Top: Brake pedal sits even with footpeg and has more room for adjustment. I don't think we will need to cut the rod anymore. Center: It is possible to adjust shock pre-load without removing the shock. Bottom: The rad shrouds do not have bolts holding them to the radiators. They use a plastic stud that fits into a rubber grommet. This is pretty cool. No more ripping the bolt through the rad shroud. Just pop it back in. |
3 Attachment(s)
http://www.gasgasrider.org/forum/att...2&d=1327603021
http://www.gasgasrider.org/forum/att...3&d=1327603063 http://www.gasgasrider.org/forum/att...4&d=1327603109 Top: Bad pic of strengthened sidestand mount. Center: 48t Talon rear sprocket. Bottom: Galfer wave rotor in rear. |
3 Attachment(s)
http://www.gasgasrider.org/forum/att...5&d=1327603306
http://www.gasgasrider.org/forum/att...6&d=1327603346 http://www.gasgasrider.org/forum/att...7&d=1327603398 Top: Front Galfer wave rotor Center: Welded on skid plate mounts. No more chasing that bar around to get the bolts started. Bottom: Back of skid plate hooks on frame so no rear bolt to put in. |
2 Attachment(s)
http://www.gasgasrider.org/forum/att...9&d=1327603683
http://www.gasgasrider.org/forum/att...0&d=1327603752 Top: skid plate attached. Bottom: Inside of new clutch cover showing the "funnel" that is molded into the cover to transfer oil into center of clutch hub. |
2 Attachment(s)
http://www.gasgasrider.org/forum/att...1&d=1327604053
http://www.gasgasrider.org/forum/att...2&d=1327604133 Top: Another shot of the clutch cover "funnel". Bottom: New clutch baskets with large oil circulation holes. |
That's a sick bike ! Thanks for the pics Clay.
|
3 Attachment(s)
http://www.gasgasrider.org/forum/att...4&d=1327604693
http://www.gasgasrider.org/forum/att...5&d=1327604760 http://www.gasgasrider.org/forum/att...6&d=1327604813 Top: New linkage Center: Rear number plate removed. Bottom: One bolt holds rear number plates on. Two tabs on each plate go into bodywork. to hold front of number plate on. Very clean! |
3 Attachment(s)
http://www.gasgasrider.org/forum/att...7&d=1327605009
http://www.gasgasrider.org/forum/att...8&d=1327605062 http://www.gasgasrider.org/forum/att...9&d=1327605143 Top: Increased gas capacity Center: Side panels snap into grommets on radiator. Bottom: Frame is made of wide flat tubing. |
2 Attachment(s)
http://www.gasgasrider.org/forum/att...1&d=1327605404
http://www.gasgasrider.org/forum/att...2&d=1327605678 Top: Magura clutch Bottom: New for 2012 in the US....tail light. |
All times are GMT -5. The time now is 02:35 PM. |
Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org