2012 300 Race Pics
 

http://www.gasgasrider.org/forum/att...4&d=1327601525
http://www.gasgasrider.org/forum/att...5&d=1327601572
http://www.gasgasrider.org/forum/att...6&d=1327601674
Top: Right side
Center: Left side
Bottom: Brake pedal mount. Note very strong tab.

http://www.gasgasrider.org/forum/att...7&d=1327601944
http://www.gasgasrider.org/forum/att...8&d=1327601987
http://www.gasgasrider.org/forum/att...9&d=1327602050
Top: Brake pedal sits even with footpeg and has more room for adjustment. I don't think we will need to cut the rod anymore.
Center: It is possible to adjust shock pre-load without removing the shock.
Bottom: The rad shrouds do not have bolts holding them to the radiators. They use a plastic stud that fits into a rubber grommet. This is pretty cool. No more ripping the bolt through the rad shroud. Just pop it back in.

http://www.gasgasrider.org/forum/att...2&d=1327603021
http://www.gasgasrider.org/forum/att...3&d=1327603063
http://www.gasgasrider.org/forum/att...4&d=1327603109
Top: Bad pic of strengthened sidestand mount.
Center: 48t Talon rear sprocket.
Bottom: Galfer wave rotor in rear.

http://www.gasgasrider.org/forum/att...5&d=1327603306
http://www.gasgasrider.org/forum/att...6&d=1327603346
http://www.gasgasrider.org/forum/att...7&d=1327603398
Top: Front Galfer wave rotor
Center: Welded on skid plate mounts. No more chasing that bar around to get the bolts started.
Bottom: Back of skid plate hooks on frame so no rear bolt to put in.

http://www.gasgasrider.org/forum/att...9&d=1327603683
http://www.gasgasrider.org/forum/att...0&d=1327603752
Top: skid plate attached.
Bottom: Inside of new clutch cover showing the "funnel" that is molded into the cover to transfer oil into center of clutch hub.

http://www.gasgasrider.org/forum/att...1&d=1327604053
http://www.gasgasrider.org/forum/att...2&d=1327604133
Top: Another shot of the clutch cover "funnel".
Bottom: New clutch baskets with large oil circulation holes.

That's a sick bike ! Thanks for the pics Clay.

http://www.gasgasrider.org/forum/att...4&d=1327604693
http://www.gasgasrider.org/forum/att...5&d=1327604760
http://www.gasgasrider.org/forum/att...6&d=1327604813
Top: New linkage
Center: Rear number plate removed.
Bottom: One bolt holds rear number plates on. Two tabs on each plate go into bodywork. to hold front of number plate on. Very clean!

http://www.gasgasrider.org/forum/att...7&d=1327605009
http://www.gasgasrider.org/forum/att...8&d=1327605062
http://www.gasgasrider.org/forum/att...9&d=1327605143
Top: Increased gas capacity
Center: Side panels snap into grommets on radiator.
Bottom: Frame is made of wide flat tubing.

http://www.gasgasrider.org/forum/att...1&d=1327605404
http://www.gasgasrider.org/forum/att...2&d=1327605678
Top: Magura clutch
Bottom: New for 2012 in the US....tail light.