Rieju & GasGas Legacy Riders Club Forum

Rieju & GasGas Legacy Riders Club Forum (http://www.gasgasrider.org/forum/index.php)
-   Enduro Electrical & Wiring (http://www.gasgasrider.org/forum/forumdisplay.php?f=19)
-   -   05 300 EC stator compatibility?s (http://www.gasgasrider.org/forum/showthread.php?t=24247)

sammittrue 02-08-2019 06:05 PM

05 300 EC stator compatibility?s
 
1 Attachment(s)
Hi my sons 05 300 EC started developing stater issues, gas gas was asking $340 for a brand new unit. Ricky stater offered $250 for rewind. my question is they look very similar to 00-07 ktm 300 stators. Are they compatible? I believe it?s a 2k2 stator. Any and all input appreciated. Thanks

Zman 02-09-2019 08:30 AM

I believe you will need to mount the stator on the GG backing plate to get the orientation/timing correct. Do the two stators look the same (coil orientation relative to the mounting holes) and do they have the same wiring? If they look very similar try it and see. If they are not very similar in orientation / clocking with same wiring you will have more work to do.

sammittrue 02-09-2019 09:45 AM

1 Attachment(s)
To be honest I?m not sure if what I took off the bike is the OEM stator. It?s completely different from picture in the manual. As far as comparing my stator to the ktm (witch I think is what this is) the pick up is slightly clocked different between the two. What a mess. Heres a photo of mine vs what I?m hoping will work after changing the wire connectors. What do you think?

sammittrue 02-09-2019 09:47 AM

1 Attachment(s)
Not sure why it didn?t upload but hers the new unit

Zman 02-09-2019 11:29 AM

That photo is really small. Can you post it larger? Can you also post the ktm and GG stator plates side by side?

Neil E. 02-09-2019 11:33 AM

Look at this topic:
http://www.gasgasrider.org/forum/showthread.php?t=23712

It shows the GG/KTM comparison for the larger 2K3.
You should be able to do the same thing with the 2K2.

(F5) 02-09-2019 11:54 AM

I got my ktm stator from Electrix for my ec300 07.

SS109 02-10-2019 08:07 PM

Learn to roll your own. ;) I've rewound stators myself with good results. It just takes patience.

(F5) 02-11-2019 01:45 AM

Hi voltage coils encased in resin on plastic forma. Swine to separate one from the other. Can't burn it off without destroying it.

SS109 02-11-2019 03:07 PM

Quote:

Originally Posted by (F5) (Post 188509)
Hi voltage coils encased in resin on plastic forma. Swine to separate one from the other. Can't burn it off without destroying it.

Correct. It can be somewhat frustrating but worth it IMO. You gotta do either the source coil, which is only one pole, or the lighting coil, which is the rest of the poles, or do both circuits completely. It isn't that hard to do. It just takes patience and a steady hand. Like I said, I've done it and I'm just an average guy with no special tools or training.


All times are GMT -5. The time now is 01:54 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org