Rieju & GasGas Legacy Riders Club Forum

Rieju & GasGas Legacy Riders Club Forum (http://www.gasgasrider.org/forum/index.php)
-   Enduro Intake/Carburetion - 2 stroke (http://www.gasgasrider.org/forum/forumdisplay.php?f=15)
-   -   2018 Ec300 Jetting Specs (http://www.gasgasrider.org/forum/showthread.php?t=23074)

Mud-Ectomy 11-06-2017 08:31 AM

2018 Ec300 Jetting Specs
 
Does anyone have any solid Jetting specs for the 2018 EC 300
Sea level, Hard Enduro stuff. A wee bit on the rich side ok.
Cheers

CDN Rick 11-06-2017 12:05 PM

Quote:

Originally Posted by Mud-Ectomy (Post 179775)
Does anyone have any solid Jetting specs for the 2018 EC 300
Sea level, Hard Enduro stuff. A wee bit on the rich side ok.
Cheers

IIRC I believe all dealers were sent info on this.
Otherwise I'm sure GGNA will have info for you. Try reaching out to them and I'm sure they will have a jetting table or better for you.

Adrian200xc 11-06-2017 09:30 PM

I went a clip leaner. It helped a lot. I was going to try a leaner pilot but I got a lectron instead. :D

Andrea#92 12-04-2017 11:26 AM

Quote:

Originally Posted by Mud-Ectomy (Post 179775)
Does anyone have any solid Jetting specs for the 2018 EC 300
Sea level, Hard Enduro stuff. A wee bit on the rich side ok.
Cheers

My 2018 EC 300 here in Italy run very good with N2ZG 2^ 42-178 (0-10 degrees, 200-1000 mt)

chunkysoup 12-31-2017 12:17 AM

Quote:

Originally Posted by Adrian200xc (Post 179795)
I went a clip leaner. It helped a lot. I was going to try a leaner pilot but I got a lectron instead. :D

How do you like the Lectron on the 2018? What did it do for the power delivery?

My 18 power comes on way stronger then my 2011...

Keg 02-17-2018 02:15 PM

NECJ #2
MJ 175
PJ 42
AS 1 1/4
1000ft alt
65 - 85 degrees f.
95-98 octane gas

Mud-Ectomy 02-17-2018 09:48 PM

Thanks Keg I will give it a try.
Went out today with
178 Main
45 pilot
#1 standard clip
AS 2turns out
And had a bog off of idle
Thanks for the help
Martin

memphis2857 02-19-2018 09:48 AM

Anyone tried the N3CH needle yet? It worked very good in the previous models. Rode my 18’ for the first time yesterday and the N1EF needle is just awful. Zero bottom end and then explodes into mega power in the mid to top. Makes it nearly unrideable in anything technical


Sent from my iPhone using Tapatalk

Gasser Nate 02-19-2018 11:40 PM

Quote:

Originally Posted by memphis2857 (Post 181558)
Anyone tried the N3CH needle yet? It worked very good in the previous models. Rode my 18? for the first time yesterday and the N1EF needle is just awful. Zero bottom end and then explodes into mega power in the mid to top. Makes it nearly unrideable in anything technical


Sent from my iPhone using Tapatalk

I have the N3cj in mine, still slightly spoogy down the pipe running stock jets, 42/175 but sings nicely everywhere else. I?ll throw a 40 pilot in when I can be bothered to clean it right up.

Gottsell 02-20-2018 03:21 PM

Has anyone tried Suzuki needle necj?
In my old yz250x ?16 i run n3ew and n3cw maybe that works for gg300.?
I dont like the stock jetting in my gg300?18 way to rich for level.


All times are GMT -5. The time now is 07:46 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org