Rieju & GasGas Legacy Riders Club Forum

Rieju & GasGas Legacy Riders Club Forum (http://www.gasgasrider.org/forum/index.php)
-   Australia & New Zealand (http://www.gasgasrider.org/forum/forumdisplay.php?f=28)
-   -   New member from New Zealand (http://www.gasgasrider.org/forum/showthread.php?t=24577)

razza 07-03-2019 01:26 AM

New member from New Zealand
 
1 Attachment(s)
Hi everyone,
New member to the forum here, and new GasGas owner too. I picked up a 2013 EC300 a few weeks back. Coming from the bike I learnt on, a DRZ400, this thing is an animal! The bike is going good so far apart from the electric start which wasnt working from when I got the bike. I had it to a mechanic whom said the starter motor bendix was damaged. So I have replaced it with the CH80 bendix as I read about on this forum. It is now working 50% of the time that I try the electric start, which is great result. I also read that on the 2013 bikes there are issues with the cables off the battery not being a thick enough gauge. I've tried to do a search on here but cant find anything specific. Can anyone point me in the right direction?

Thanks, Razza

Pygmygod 07-03-2019 01:44 AM

Nice upgrade from a heavy ol' tractor (DRZ)

Does this thread help?
http://www.gasgasrider.org/forum/sho...ght=gauge+wire

Anders 07-03-2019 03:33 AM

Congratulations and welcome to the club! You will have a lot of fun with that bike.

(F5) 07-03-2019 02:07 PM

On ya.

1. Read the jetting section and buy an RM250 needle or similar. You won't believe the improvement if it still has the std needle.

2. Take the small sidecover off the bendix runs in. It wears oval so the bendex moves away from the gear. As it skews it will get destroyed in short order now it is worn.

The fix is simple. You van buy an insert from any bearing shop for mere dollars, that has same ID as shaft, then bore the cover to fit. Like new but better.

Think I bought spares when I did my mates if you can't find. Heck I made a jig to do the drilling. Wonder where that is?

(F5) 07-03-2019 05:55 PM

Actually I found the jig,

but I think that the 13 is mounted slightly differently than my mates like 15ish. But principle should be the same. Just drop the cover off and see if there's any sideways play on the bendix.

gg3 07-04-2019 03:37 AM

Hi,good choice.

tonyraft 07-06-2019 06:11 PM

Where you located

razza 07-09-2019 03:42 AM

Quote:

Originally Posted by Pygmygod (Post 190834)
Nice upgrade from a heavy ol' tractor (DRZ)

Does this thread help?
http://www.gasgasrider.org/forum/sho...ght=gauge+wire

Thanks that does help. I will do some more reading up on the topic.

razza 07-09-2019 03:43 AM

Quote:

Originally Posted by Anders (Post 190836)
Congratulations and welcome to the club! You will have a lot of fun with that bike.

Thanks Anders. Already having a blast on it!

razza 07-09-2019 03:48 AM

Quote:

Originally Posted by (F5) (Post 190846)
On ya.

1. Read the jetting section and buy an RM250 needle or similar. You won't believe the improvement if it still has the std needle.

2. Take the small sidecover off the bendix runs in. It wears oval so the bendex moves away from the gear. As it skews it will get destroyed in short order now it is worn.

The fix is simple. You van buy an insert from any bearing shop for mere dollars, that has same ID as shaft, then bore the cover to fit. Like new but better.

Think I bought spares when I did my mates if you can't find. Heck I made a jig to do the drilling. Wonder where that is?

Thanks F5. I understand the previous owner had the jetting changed by Dirt Action Services down here in Christchurch. Not sure what these changes entailed though.

I will check out the sidecover at the bendix too. Ill report back on what I find. The bike only has 100 hours on it, and the previous owner removed the electric start systems for at least some of that time, so hopefully no issues with it at the moment.


All times are GMT -5. The time now is 12:48 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org