|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Pegs for 2011 EC300
Is there any pegs that fit this bike, w/o modifications?
I have searched a few times with mixed conclusions. Non-pivoting type peg's.
__________________
Bryan 2013 Husaberg TE250 - Current 2011 GasGas EC300 - OLD STEED 2011 Husaberg FE390 - OLD STEED 2010 Yamaha WR250F - OLD STEED #53B I dream of a better tomorrow, where Chickens can cross the road, and not be questioned about their intentions. |
#2
|
||||
|
||||
You will have to notch/grind the inside rear corner of the right side peg to clear the brake pedal on fold up with any peg. Anything for a Yamaha YZ fits.
|
#3
|
|||
|
|||
ahh. I see.
__________________
Bryan 2013 Husaberg TE250 - Current 2011 GasGas EC300 - OLD STEED 2011 Husaberg FE390 - OLD STEED 2010 Yamaha WR250F - OLD STEED #53B I dream of a better tomorrow, where Chickens can cross the road, and not be questioned about their intentions. |
#4
|
||||
|
||||
Yep! Almost anything Yamahaish. I pulled the pegs off my 2004 WR250F and they slid right on it.. But as Glenn has said you need to make sure they have enough clearance to pivot back on the right where the brake pedal runs. I try and look for ones that are easy to grind or cut and will still have good strucural integrity afer doing so. Can't remember what brand I have on now but they're good Can find out for you.
|
#5
|
|||
|
|||
Sure, let me know please.
__________________
Bryan 2013 Husaberg TE250 - Current 2011 GasGas EC300 - OLD STEED 2011 Husaberg FE390 - OLD STEED 2010 Yamaha WR250F - OLD STEED #53B I dream of a better tomorrow, where Chickens can cross the road, and not be questioned about their intentions. |
#6
|
||||
|
||||
I ran the Moose hybrids (big, stout pegs) with a fair bit ground out of the rear inside corner. The peg would pivot about half of the left one before running into the brake pedal.
Hit a log hard enough and clang, clang, clang goes the brake lever Still you'll have stronger pegs than stock, even if they don't pivot as far ...
__________________
Steven Beane #275 PlusOnePerformance - Superior Service the World Over - Dearborn MI AMA District 14 (Michigan) Officer afterhourscycle.com Michigan's Beta and TM Race Headquarters |
#7
|
||||
|
||||
Talons are what I am running. Took a bit of work to shave the right peg back enough to clear the brake but all done and holding up well. |
#8
|
|||
|
|||
since I got these http://www.raptortitanium.com/shop2/...?id_category=6 I don't want to have the pivotpegs any more...
__________________
4 strokes are only good for power generators |
#9
|
|||
|
|||
Titanium eh?...... economy must be paying will in Good Ol Germany
__________________
Bryan 2013 Husaberg TE250 - Current 2011 GasGas EC300 - OLD STEED 2011 Husaberg FE390 - OLD STEED 2010 Yamaha WR250F - OLD STEED #53B I dream of a better tomorrow, where Chickens can cross the road, and not be questioned about their intentions. |
#10
|
||||
|
||||
Those Talons look twice as strong as the frame tabs. My '12 came with a set of S3 pegs which are very nice.
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New 2011 EC300 | erniebearskin | General Discussions & Announcements | 14 | 05-06-2012 12:53 AM |
Will any year CR250 pegs fit on the 2011 gassers? | thumperrider1 | Enduro Chassis & Body | 4 | 03-26-2011 12:43 PM |
IMS pegs on 2008 EC300 | lineman12345678 | Enduro Chassis & Body | 6 | 01-11-2009 03:24 PM |