|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Rear wheel spacers dimensions needed
Hello guys... would anybody be so nice and measure dimensions of rear wheel spacers for ec 250 2008? I want to have them machines because it is difficult to buy those in Slovakia... thanks a lot
Edit: as i have figured out from used bearings and seals all spacers 20mm ID, right spacer 25mm OD, left spacer 25/32 mm OD, spacers between two bearings is 20x42x2mm. So i need to confirm these dimension and add lenghts for all 4 spacers.. thanks a lot Last edited by mrfreezer; 09-06-2017 at 12:12 PM. |
#2
|
|||
|
|||
Here is the dimensions I used to make my own spacers (measured in inches). These dimensions have been rounded off a bit, but you can probably deduce the original metric sizes. To convert divide the inches by .03937 for mm.
If you have trouble I can dig out the original spacers and measure them for metric dimensions. These fit 2011, should work for other years.
__________________
2011 EC250E |
#3
|
||||
|
||||
I bought some aftermarket ones off some French site by searching for the part numbers. Can't remember. But well made and hard anodised.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#4
|
|||
|
|||
Neil... thanks a lot.. it helped... I have converted it... can anybody check those other spacera for me?
|
#5
|
|||
|
|||
doesn't the washer have a step on it?
__________________
2003 txt250 Pro 2013 Ossa 280i |
#6
|
||||
|
||||
Yes it does
__________________
02 EC 200 03 MC 250 88 VT 800 01 TXT 280 |
#7
|
|||
|
|||
That's a good point. There is a small step that's intended to keep the spacer from falling out when the wheel is removed. I found them to be a nuisance. They push out some of the grease that I fill the lip with so I omitted them.
I'll dig out the originals, but I'm sure I machined the step mostly off for the same reason.
__________________
2011 EC250E |
#8
|
|||
|
|||
guys... can anybody measure the long spacer in the middle of the rear hub? mine is damaged so I can not figure out how long it have to be... the damaged one is 100.5mm long
|
#9
|
|||
|
|||
I won't be having my wheel off for a while, but surely the dimension can be measured from the inner wheel bearing race on each side?
__________________
2003 txt250 Pro 2013 Ossa 280i |
#10
|
|||
|
|||
thanks, but I need to have new spacers done before I start to disassemble my wheel
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
wheel spacers | kpuc11 | Enduro Chassis & Body | 9 | 10-16-2016 05:14 PM |
Need inner wheel spacer dimensions | GGRider01 | Enduro Chassis & Body | 0 | 04-29-2016 12:28 PM |
ec 200 wheel spacers | gump147 | Enduro Chassis & Body | 6 | 03-05-2015 10:35 AM |
carb dimensions and advice needed | BryanMcc | Enduro Intake/Carburetion - 2 stroke | 2 | 09-30-2012 12:59 PM |
dimensions needed ltr pv cover | mountain thumper | General Discussions & Announcements | 6 | 05-04-2010 06:29 PM |