|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
correct seat ???
this has been playing on my mind for a while and forgive me if its petty.
right i supposedly have a 2003 ec300 as per its registration and log book. I've looked at the part number on the base of the seat and it says BE250010015 so I've checked it on line it comes up as 2000 250 ec the seat does not fit snugly and bows were it rest on the tank leaving a gap and if i push it flush it will not line up at the back, as to be a inch to short. I've looked for the correct one for the blue bike and its BE300310015 ???? is there a difference in the seats from a 99 or 2000 to my 2003 i gather the part numbers will differ do to colour or cc but not sure about years again sorry if this is bone, but it would rather get the correct one and be done properly ask want to restore all the plastics, graphics and seat cover thanks grant
__________________
03 ec300 honda cr500 94 |
#2
|
|||
|
|||
is there a way of telling the bike correct age through it chassis numbers
__________________
03 ec300 honda cr500 94 |
#3
|
||||
|
||||
The 99 seat is a different design than the 2000 and newer. The 99 fuel tank doesn't fit into the seat like the newer ones. Post a couple pics of your problem. I wouldn't think there should be a problem fitting a 00' seat on a 03' bike.
__________________
Noah 2000 EC250 with 2011 transformation kit, KYB SSS forks, MN street title 16' Ski-Doo XS Renegade X 1200 4T 16' Specialized Fatboy trail 02' ZRX 1200r R.I.P. 72' Olds 500ci, Batten Heads, Street/Drag car, former CarCraft magazine centerfold (has-been) 15' TW200 |
#4
|
|||
|
|||
will try, just stripping down to check the piston and barrel and have a winter clean.
i have noticed the part that sits up on the tanks has been bent and has gone week. could be helping
__________________
03 ec300 honda cr500 94 |
#5
|
|||
|
|||
http://www.gasgasrider.org/forum/att...8&d=1374608813
this is the best pic, but is hard to see the problem properly
__________________
03 ec300 honda cr500 94 |
#6
|
|||
|
|||
Seems I remember the fuel tank and seat changed slightly in 2001 so if the 2 are mismatched there is minor fitment issues.
__________________
jeff '00 XC250 (mine) LTS front and rear suspension, power valve cover, carb jet kit and rear chain glide, RB Designs head mod, BRP tall triple clamp, backyard foot-peg lowering conversion. '04 EC250 (the kids) (he can do his own mods haha!) |
#7
|
|||
|
|||
Thats what I was thinking, as it could do with being a touch longer
__________________
03 ec300 honda cr500 94 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Correct warm up procedure | Chevva1 | Enduro Engine - 2 stroke | 4 | 06-09-2013 08:14 PM |
this may not be the correct place to ask, but... | compmoto | SouthEast United States | 6 | 10-30-2010 02:10 PM |
Correct plug? | Dunk | Enduro Electrical & Wiring | 5 | 07-24-2009 10:33 AM |
Fork seals, Do I have them installed correct | ramcclure200 | Enduro Suspension | 10 | 04-17-2008 12:00 PM |
correct jetting for my 01 xc200 ? | fasternat | Enduro Intake/Carburetion - 2 stroke | 4 | 02-28-2007 12:19 PM |