|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Checking my Rekluse 3.0 after 140-ish hours
I like to check the bike over after each race.
After last weekends' rock-fest race with lots of clutch-slipping Rekluse-testing hills and rocks, I decided I would focus on the clutch basket this time around. I sent an email to Rekluse to get the minimums. They sent, Quote:
The odd thing is that all of my steels measure 1.05mm. There is no "thinner disk," they are all the same. As well, my clutch fibers measure 3.05mm. Nothing close to the, "2.75mm to 2.85mm (min 2.68mm)" as stated in the manual. I'm guessing (I can't recall) that the the "all-1mm" steels were some special Rekluse solution for the Gasser. And, perhaps, the Rekluse fibers are thicker than OEM? I have an email into Rekluse. |
#2
|
|||
|
|||
Now I remember.
I got the "Honda Frictions Mod." Thicker fibers and all the steels are the thin ones. All good. |
#3
|
|||
|
|||
I did that mod too, I have the specs on a piece of paper stored with my stock gasser clutch parts. I will take a look at it when I get home because I wrote the measurements for the Rekluse made steels and fibers.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#4
|
|||
|
|||
Is the cr mod for the Rekluse only or are there any other benefits?
I am still on my oem disks at about 300hrs and apart from the oem clutch squeak (not changed from new) all is fine. I just bought a 2013 clutch cover hoping it will add some oil to the center
__________________
2003 txt250 Pro 2013 Ossa 280i |
#5
|
|||
|
|||
In North America the CR fiber discs are 1/3 of the price of oem Gasser fibers and there are a greater selection on disc types and mfgs.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#6
|
|||
|
|||
Ah ... ok. Thanks
__________________
2003 txt250 Pro 2013 Ossa 280i |
#7
|
|||
|
|||
No problem.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#8
|
|||
|
|||
Having measured and checked everything, I have bolted it up.
Time to put new nubbies for next week's race. |
#9
|
|||
|
|||
Just picked up a used rekluse for my 12, ec300. What CR friction plates and steels are you using? Since it's used I rather just put CR mod in and not worry.
Any part numbers of each? |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Double checking year of my bike | Munch | Enduro Other... | 10 | 06-25-2016 10:43 AM |
125+ Hours. Time for a top end job | AZRickD | Enduro Engine - 2 stroke | 12 | 12-24-2015 04:02 PM |
Checking in here. | rockertom | General Discussions & Announcements | 3 | 07-18-2011 04:09 AM |
Checking for proper power valve operation 2003 EC250 | SideshowBob | Enduro Engine - 2 stroke | 4 | 04-08-2010 01:00 PM |