|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
CDI/ECU Placement??? Wiring loom , speedometer
Hi all,
I have a gas gas ec 300 2004, I am currently building it from scratch. The previous owner put in over sized piston rings and blew the top. He took the entire bike apart and got fed up with the project so sold it me. Over the years I have been slowly rebuilding it and I'm getting closer to firing the newly built engine for the first time. I have come to the wiring loom , CDI unit and speedometer but can not find the route where the wires go and mainly where the cdi unit sits. Can someone please advise me on the above. Thanks in advance |
#2
|
||||
|
||||
The CDI sits on a small flat piece of plastic bolted inside the air box on right side fender just far enough up to clear the filter. The wires come through the upper right front of the air box and cross over above the rear shock and go down to the lower part of the frame going forward. You should see some tabs that are welded to the frame to bend over the wire loom and hold it in place. When you get to the front of the frame/cradle, the coil wires continue around to the right side where the coil bolts on. The rest of the wires go up the cradle to the steering stem, there should be a single yellow wire with a connector on it that the voltage regulator connects to and mounts on the center cradle . The rest of the wires continue up the center frame tube and around the steering stem on the left side into the head light area.
Hope this makes sense.
__________________
07 EC 300 06 Gold Wing (2) 06 CRF 150 F |
#3
|
||||
|
||||
I don't have a 04, but I can take some pictures of my half-way dismantled 06 if that is needed. Please let me know.
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#4
|
|||
|
|||
Quote:
|
#5
|
|||
|
|||
Yes please. I'm scrolling through Google images trying to figure it out any more images you could provide i think will be a great help. Thank you
|
#6
|
||||
|
||||
Quote:
Sent fra min YAL-L21 via Tapatalk
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
Tags |
cdi, ecu, loom, speedometer, wiring |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Wiring loom part number?? | motopsycho87 | Enduro Electrical & Wiring | 0 | 04-15-2016 09:35 AM |
Wiring loom | spooly | Enduro Electrical & Wiring | 8 | 01-12-2015 05:33 PM |
EC 1997 wiring Loom | EC250 | Enduro Electrical & Wiring | 5 | 12-24-2014 04:24 PM |
can anyone help with wiring loom routing | dirtjunky_uk | Enduro Electrical & Wiring | 3 | 08-05-2011 01:04 AM |