|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Swingarm and Linkage Bearings
Howdee,
Anybody have a better recommendation for swingarm and linkage bearings? I replaced all of those last spring, and this year they're shot already. This is really getting old. My kid's KTM is ridden just as hard, and its swing arm bearings are fine. My XR250 went five year w/o needing bearings. Anyone try allballs racing bearings? I am all ears. Thanks. blitz |
#2
|
||||
|
||||
Quote:
I think you cant do much better than stock. What did you run before?
__________________
2002 Gasgas EC250 (gone not forgotten) 2012 Ktm 300xc 2001 Gasgas EC300 Lifes journey is not to arrive safely at the grave in a well preserved body, But rather to skid in sideways totally worn out shouting holy cow what a ride !!!! |
#3
|
||||
|
||||
I used All Balls. No problems.
|
#4
|
||||
|
||||
Has anyone put greese nipples into the rear linkage before? seen some people mod Husky linkages, might be an idear for longer bearing life?
|
#5
|
||||
|
||||
Bought the bike used, so don't know the original. When I bought the bike, I pulled everything apart and greased it. Looked OK. (It was a low hour bike). Went to grease it the following year (maybe put 40 hours on it), and the bearings were destroyed. Of course, I was pressed for time, so I called GoFasters for the kit they sell (Moose, I believe) instead of the individual bearings and seals (didn't want to fish through the fische)
Maybe rode 35 hours this year (see broken wrist), and although the needles aren't flat like last time, the bushings are worn, especially the swingarm bushings. No heat treat there. What cheap junk. Have you had your linkage apart in that 300 hours? You might be in for a surprise if you haven't. Is there an OEM kit? Or do I have to pick out pieces? I don't recall a kit on the fische. If no kit, I will put together a spreadsheet, i guess, that covers the bushings and bearings, and sent it off to GoFasters for OEM unless someone has had good luck with AllBalls ( iancp5 has) or Pivot Works. It's not that I am cheap, i just don't have much time to jack with this. It's insane that someone sells a kit which lasts only 40 hours of not very hard riding. Nice quality control. Jeesh. Thanks very much. blitz |
#6
|
||||
|
||||
I have just took apart my linkage and it is sitting out in front of me. It has almost no play at all. The only reason I am replacing them is just for good measure and I want my bike to feel new again.
If it was me I would try OEM before an aftermarket kit.
__________________
2002 Gasgas EC250 (gone not forgotten) 2012 Ktm 300xc 2001 Gasgas EC300 Lifes journey is not to arrive safely at the grave in a well preserved body, But rather to skid in sideways totally worn out shouting holy cow what a ride !!!! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Swingarm Bearings | carlg | Enduro Suspension | 2 | 02-25-2010 07:12 PM |
Swingarm linkage/bearing kits | gasIdaho | Enduro Suspension | 1 | 02-03-2009 01:29 PM |
Swingarm bearings | rupecopp | Enduro Chassis & Body | 0 | 06-16-2008 03:56 PM |
ec200 swingarm bearings | rupecopp | Enduro Engine - 2 stroke | 2 | 07-30-2007 12:54 PM |