|
All Other Bikes... KTM, Husky, VOR, Husaberg & Hondayamazuki... |
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
GG parts crossover to '14 Beta 300rr
I'm seriously looking at a '14 Beta 300rr. I'm hoping some of U Beta 2t owners know if some of my GG parts will fit the Beta. I have Force radiator guards and another brand with just side impact protection with no name on them. Shark fins, EE bark busters, Cycra bark busters, footpegs, fmf tubine core 2 with spark arrester. Trying to save a few bucks. Thanks.
__________________
'14 Beta 300rr '05 GG DE300 '03 GG EC250 '01 XR440 '09 FZ1 |
#2
|
||||
|
||||
Sorry, but looking at the list I think handguards may be all you could salvage.
PlusOnePerformance
__________________
Steven Beane #275 PlusOnePerformance - Superior Service the World Over - Dearborn MI AMA District 14 (Michigan) Officer afterhourscycle.com Michigan's Beta and TM Race Headquarters |
#3
|
|||
|
|||
Not a whole lot of KTM to Beta cross-over, either. Some, not much.
|
#4
|
|||
|
|||
.. Maybe the radiator guards you could adapt.. maybe the ktm pegs could fit... Really the hand guards are probably the main addition.. but you getting a 14' and put some old stuff on it? I don't know.. you get a beautiful bike and put some scratched up stuff to put on it?... maybe just hold off and just get the rear disc guard and other key stuff from Beta on the BYOB program.. seems a bit of a sacriledge
|
#5
|
|||
|
|||
Quote:
__________________
'14 Beta 300rr '05 GG DE300 '03 GG EC250 '01 XR440 '09 FZ1 Last edited by flybars; 07-28-2013 at 02:04 PM. |
#6
|
|||
|
|||
Fork bleeders are the same as a KYB (5mm thread dia.), larger than the WP units. Air filters won't fit, I can just tell you by looking.
All I've done to my Beta is carefully grease it, install heavier springs for my weight, have TwoWheels revalve my fork and install radiator guards, pipe guard and a BRP submount for my Scotts Damper I had laying around. Really don't know if the damper would be needed, if I didn't have it already. Heavier tubes are a good idea, but I really like the stock Michelins, especially the oversized balloon (140/80) on the rear. Jetting is stock, and I haven't messed with the PV adjuster yet either. Fork springs from a Yamaha SSS fork like my 2006 YZ fit, along with KYB rear springs, although KYB's rears have a slightly larger dia. I do like that Beta already has all kinds of aftermarket parts available already, which I'll look at as I wear out stock parts.
__________________
"Conviction is a luxury of those on the sidelines." '13 Beta 300RR - race bike '02 GG300XC - "Billie Baroo" '01 DR650 '02 GG 280 Pro '06 YZ 250 '07 WR450 '00 TT125RL '94 YZ200 - custom keeper |
#7
|
||||
|
||||
Quote:
I have a '14 300RR reserved and a whole garage full of KTM parts. I'll list what will swap when I get a chance if I pick it up.
__________________
04 Montesa 315R, 07 EC300, 21 KTM Erzberg 300, 21 Sherco 300 SEF-F, 23 KTM 690, 23 Rieju Mr Pro 300 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
I'm buying a Beta 300RR | Hawkeye | All Other Bikes... | 126 | 05-20-2013 10:29 PM |
2012 Parts crossover | Steve Croxton | General Discussions & Announcements | 13 | 01-26-2013 08:00 PM |
Another Parts Crossover Question | carlg | Enduro Chassis & Body | 1 | 11-28-2010 11:37 PM |
250/300 clutch parts crossover | Skidad | Enduro Engine - 2 stroke | 5 | 01-09-2008 11:54 AM |
Parts Crossover idea | Phattaff | Suggestion Box | 3 | 08-21-2006 05:43 PM |