|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Rear brake clevis
Hi all and I have a question,
the clevis that hooks the pedal to the master cylinder is wallowed out. It appears from the breakdown poctures that it is not sold separately. Does anybody have a 'fix' or does one of the Fasstco clevis #'s work? Also when I put the mecca brake lever it appears that the master cylinder shaft is offset to the inside of the pedal centerline, could the master cylinder mount be bent in ? Or something else? It seems to me that the master cylinder rod should go straight down to the pedal hookup. Couldn't tell from before cause the old pedal was trashed. Thanks in advance
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#2
|
||||
|
||||
I can't speak for the plunger being bent, or a bent brake mount, but that sounds reasonable. Someone here posted a nice picture of the fix for this. I couldn't find the picture, maybe it's in my pm's. I'll look. Here's the quote:
Originally Posted by GMP I filled the hole with HTS-2000, drilled and tapped it M6. Then get some thin walled steel spacers or M6 weldnuts, and run an M6 bolt with one on each side and a nut on the back. This way, the bearing surface in the pedal hole is eliminated (no wear), the spacers slide in the clevis. As a bonus on the older bikes with the pedal height/stop bolt you can cut the bottom out of the clevis slot and the pedal can be removed without touching the bolt/spacer setup. Very handy for on the trail removal. In that thread there was a cool reference to a Zeta brake clevis. Super bling. Probably super expensive.
__________________
Mike Sheetz OMRA #21AA What will I be riding next? Christini GG 300? '15 KTM 300 XC-W '08 EC 250 (Gone to new happy owner) Gran Prix Cycle LTR Suspension RB-Designs Last edited by roostafish; 12-14-2009 at 10:11 PM. Reason: Found what I was looking for |
#3
|
||||
|
||||
I Googled 'Zeta Brake Clevis' and got several sites. Not a bad price @ $25.00 but no application for GasGas. Anybody know of a cross reference ?? Same thing I ran into with the Fasstco clevis.
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#4
|
||||
|
||||
Honda CR, some thing like 90 to 2000 you have to drill it a tiny bit overesize. Four bucks and change.
|
#5
|
||||
|
||||
Sweet ! I'll check it out,thanks Widebear
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#6
|
|||
|
|||
i have been in contact with Fasst and given the dimensions for the clevis. i expect to know something today or tomorrow on a clevis that will work for us. i will post the findings when i get them.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Broken rear shock clevis | gasgasquebec | Enduro Suspension | 5 | 09-27-2010 07:35 PM |