|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
fuel consumption
my 2000 GasGas 300 ec compared to a friends 02 KTM300 exc my bike has a drink problem, we both have 12L fuel tanks and similar riding style etc but he still has a 1/3 of a tank left when have to go on reserve, my jetting is 40 - 180 - 2nd clip from the top float level is spot on and there is no fuel leaks on the bike
Could I drop the needle putting on the top clip and say come down to a 178 or even a 175 main? But leave the pilot circuit as it is? |
#2
|
||||
|
||||
Look here for something similar in elevation etc http://www.gasgasrider.org/forum/showthread.php?t=2162
I'd say the 180 is way to rich 175 at least
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#3
|
||||
|
||||
What needle are you running? That era gasgas came with an n1ef needle or close to it and other needles will work better and provide better efficiency.
And fuel consumption is helped by dialing in the Squish - have head machined to optimize combusion & compression ratio. jeff
__________________
|
#4
|
|||
|
|||
Quote:
|
#5
|
||||
|
||||
What you doing on the computer you should be out riding , I'm stuck working in milford haven , n1ef is not the best needle , and doing the head makes a big difference too.
|
#6
|
|||
|
|||
Quote:
what needle you think i should get? i have been on the look out for a CCK needle but not seen one |
#7
|
||||
|
||||
Get a yz or rm needle , cck you can get from Allen's performance , think I have a cck at home but I'm in milford for the next few weeks working .
|
#8
|
|||
|
|||
If you're concerned about fuel consumption, don't use a CCK needle. The N1EF that is in there now will get better milage than the CCK. Your best bet for better fuel milage will be using a Suzuki triple taper NExx needle.
|
#9
|
||||
|
||||
I agree my experience was the same. While I liked how the CCK made my 300 run it used a lot more fuel than the N1 needle. On my 250 I switched to a NEDW (Suzuki needle) and mileage is as good as ever and power delivery is strong and smooth from idle to mid rev. A little flat in the middle but an RB head mod took most of that away. Still revs out pretty good on top. This is my favorite jetting I've had on any of my gassers. I'm sure it could be made even better if I was any good at jetting but I like it so much that I don't mess with it.
|
#10
|
|||
|
|||
You say "similar riding style" but are you sure? It may not just be a fuel/jet issue.
Bikes geared the same? Does one of you ride a gear higher or lower than the other one more often than you realize? Those two can contribute to a fair amount of MPG differences.
__________________
-Keith '08 EC250 and some other bikes. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fuel cap fix | motopsycho87 | Enduro Chassis & Body | 3 | 03-07-2014 10:24 PM |
help with fuel tap please | jilljoy | General Discussions & Announcements | 3 | 09-07-2011 04:40 PM |
Jetting help - Fuel consumption | Jakobi | Enduro Intake/Carburetion - 2 stroke | 17 | 11-12-2010 01:05 AM |
gas consumption 200 race pace? | stainlesscycle | Enduro Engine - 2 stroke | 7 | 02-08-2010 09:11 AM |
Fuel range and fuel light | sanderjavant | Enduro Engine 4 stroke (including EFI & Exhaust) | 6 | 01-05-2008 02:35 AM |