|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
PV shaft movement (video) 2010 ec300
Hi all,
Can anybody tell me if this is right? I have read extensively about the PV but haven't found my answer really. Under gentle acceleration I hear what sounds like a reverberation from what may be this. It kind of sounds like it could be this just getting the sweet spot of vibration that makes it 'flutter' and wobble until the revs and/acceleration increases. Should it have this movement, and if not, any clue to what's caused it. Thanks in advance, http://http://youtu.be/l1-kEXvzuD0 Last edited by justsam; 04-03-2014 at 06:12 PM. Reason: Ballsed up the link! |
#2
|
||||
|
||||
that seems like it has more slop than the ones I have pulled apart. Maybe try to shim it with some washers.
|
#3
|
||||
|
||||
__________________
2012 - XC 300 Racing Seattle, WA |
#4
|
|||
|
|||
Thanks fellas, although that video doesn't actually deal with the part I have shown in the video. My video is the bearing and shaft end inside the left side PV casing.
As far as shinning it, whilst that is an option, if it's not right if rather deal with the actual issue as to why it's happening rather than just hiding the symptom of the issue by shinning it. Any ideas where this play may have developed? |
#5
|
||||
|
||||
Ok.
Here is another good video and he talks some about adding washers or at least where you would add them. I would recommend you take the complete assembly apart and clean up. Maybe a bearing is bad... If you do so this video will help you put it back together. Also use the search feature in the forum. There is a lot of info that has been discussed before. http://youtu.be/FQJs2qM3rT8 Sent from my iPhone using Tapatalk
__________________
2012 - XC 300 Racing Seattle, WA |
#6
|
|||
|
|||
Here is a two part video on fixing pv rattle on a GasGas,
http://www.youtube.com/watch?v=dI0fUUHaDjQ
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#7
|
||||
|
||||
I have just cleaned mine up and noticed the same amount of play until the screws on each side are fully tightened which then encapsulates the bearings with the washers and stops most of the excessive movement.
Check the washers on each side are tightened . Cheers Mark
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2010 EC 300 Water pump shaft snapped & bearing collapsed | justsam | Enduro Engine - 2 stroke | 207 | 03-16-2017 04:25 PM |
Clutch Slave. How much movement? | Marki | Enduro Engine - 2 stroke | 5 | 04-26-2013 12:38 PM |
clutch slave movement ? | jhendr3702 | Enduro Engine - 2 stroke | 0 | 03-16-2011 03:44 PM |
Nambotin EC300 video | gasgasman | Pictures & Videos | 4 | 07-05-2010 10:22 AM |