|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
So today I replaced the leaking float needle with one from a 2014 model it was 18mm long and old one 15mm thought this was odd as same carb maybe mine had One from an as1? But after a bit of bending I got the float hight to 10mm and while I had the carb apart dropped down to a 40 pilot jet readjusted the air screw now 2 turns out. This has seemed to clean up the whole range no more burble at 3/4 throttle. Still a little rich but a lot better and there is more of a kick to it in the lower revs found that it actually sometimes breaks the traction when going up a technical section. Guess the Suzuki needle will make it more liniear and KTM needle more of a kick?
750ft 15c in sunshine mode |
#12
|
||||
|
||||
The stock N1EF has a very short straight section, which is also overly rich. It then tapers off quickly. You usually end up with nice off idle and a lean hole in the middle, or a fluffy bottom that snaps to life as it clears out.
Both the Suzuki and Yamaha/Ktm needle has a longer straight section which really helps to dial in the idle and off idle. The Suzuki is probably a bit leaner feeling off idle, and has much less taper through its profile. Steady supply of fuel. The Yamaha/Ktm is a dual taper and you really do feel the transition between the two. It almost leaves a small lean area in the middle/upper rpm where the engine transfers onto the pipe. You end up with a smooth grunty bottom end, and a wild top end on the pipe, with a strong transition between the two. |
#13
|
|||
|
|||
Quote:
|
#14
|
||||
|
||||
My knowledge is limited as. I only really know the ones I've played with.. Pretty small scope in the big picture I'm sure!!
|
#15
|
||||
|
||||
Bit like. . . Ahh maybe I should behave. I've had some Friday drinks. Let's just say . . Nope probably can't say that here. People might get offended.
Boobs. Hehehehe. Hooray for boobies. Jeez, real mature Dave. Am I 13?
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#16
|
||||
|
||||
Pop quiz.
Who am I, is this me? Am I one or thirteen? I've gone cold, hard to deal Used to stand where I kneel
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#17
|
||||
|
||||
I don't know why shes leaving or where she's gonna go!
For twenty four years I've been living next door to.. |
#18
|
||||
|
||||
What are you on about? Oh wait. .
Right. That's clever.
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#19
|
|||
|
|||
Well I got the n3ch needle today so it?s in the bike and what a difference haven?t rode it yet because of there being to many people around but just of the bench it sounds a lot different a lot smoother idle had to wind the idle screw back about 2 turns. Overall it sounds a lot cleaner. Im going out on it tonight so will update this post but it seems like a totally different bike. Current setup
N3ch #3 178 main 40 pilot 1 1/2 air screw 735ft 15.2c |
#20
|
|||
|
|||
The bike is totally different with this needle pleanty of grunt in the bottom end and nice to ride and then get on the pipe and wow front end up on ever straight going past loads of bike on the pipe in the hare and hound even had someone ask me what I had done to it to make a gasser sing like that I think the should come out the factory like this. Removed the plug and a lovely brown colour I am really impressed with this bike now
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Jetting (needles) 2013 gasgas ec 250 | nickp | Enduro Intake/Carburetion - 2 stroke | 7 | 11-03-2013 02:25 PM |
2012 300 jetting | bones150 | Enduro Intake/Carburetion - 2 stroke | 3 | 05-10-2012 05:56 AM |
2012 300 JD jetting kit | mblazer11 | Enduro Intake/Carburetion - 2 stroke | 11 | 04-17-2012 10:12 PM |
Where to buy needles. Other jetting questions. | IDAHOSPUD | Enduro Intake/Carburetion - 2 stroke | 1 | 11-07-2011 02:08 PM |
JD Jetting Spreadsheet - anyone know codes for JD needles ?? | DaveH | Enduro Intake/Carburetion - 2 stroke | 1 | 02-13-2011 09:40 AM |