|
Enduro Suspension Tuning & maintenance of Enduro forks, shocks, etc |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
KYB Crossover
Hi All,
I have read that the reiger racing shock spring is the same as a KYB, anyone has any parts crossover listings for the springs/weight in KYB? Looks like mine is a bit soft for my at 90kgs, but having trouble finding a reiger one. Cheers |
#2
|
||||
|
||||
Where are you located? You can buy springs directly from Reiger, they are not very expensive (I think I paid 80 Euro).
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#3
|
||||
|
||||
Another idea to add, I recently ordered a spring from Cannon and it got to me within a couple of days. $119.
Get out your caliper/tape and measure your spring I.D. & length, and they will likely have what you want in stock. (Try a YZ250 match, 59mm x 270mm. This was 10mm longer than my stock spring, but it fit just fine. Also, if you haven't measured a spring before recognize that the top and bottom I.D.'s are slightly different, in this case 59mm is the smaller end). Be aware that they measure their spring rates by Kg/mm, and GasGas (at least in the 2018 manual) uses N/mm - which is slightly different. You want to make sure you're getting the new spring rate you want! Jeff https://www.cannonracecraft.com/contact 405-524-7223
__________________
'18 GG XC 300 '05 GG DE 300 '01 GG txt 321 |
#4
|
|||
|
|||
I'm in NZ, so pretty far from all the parts.
Do reiger have a parts listing or do you need to get in contact first? |
#5
|
||||
|
||||
Quote:
Reiger can be contacted via info@reigersuspension.com
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#6
|
|||
|
|||
tried to PM, did it come through?
|
#7
|
||||
|
||||
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#8
|
|||
|
|||
Got it thanks. Hopefully I can get a spring in the 85-90kg range now. Also after the bearings at either end of the shock.
I have read the bush and needle roller are not "needed", anyone replaced them with anything else? I just put new rose joint swivels in but there is play in the upper due to the bush being worn. The needle bearing is new as well, they are 6 bucks locally but cant find the bush to replace Cheers |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Air filter crossover | adv rider | Enduro Intake/Carburetion - 2 stroke | 3 | 04-30-2016 09:36 AM |
Gas cap crossover | forgiven | General Discussions & Announcements | 3 | 09-07-2014 08:19 PM |
Crossover | Rabbitist | General Discussions & Announcements | 1 | 01-25-2012 09:16 AM |
Crossover-KTM Rads ? | husley | General Discussions & Announcements | 2 | 04-10-2011 07:28 PM |
Gas cap crossover help | hotshot | Enduro Chassis & Body | 1 | 03-01-2011 08:35 PM |