|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
I live in the Peak District in the UK. We generally do not have shops that sell nuts and bolts other than engineering suppliers that only open Monday to Friday. These nuts are definately 14mm so I'm going to order some from Gas Gas Uk.
|
#12
|
||||
|
||||
Wait till Monday and hit the engineering shop Quicker and most likely cheaper than genuine too.
|
#13
|
||||
|
||||
Would you not still be getting extra torque from the extra length of the wrench?
__________________
2018 EC 300 |
#14
|
||||
|
||||
Quote:
http://www.finishing.com/118/94_crows_foot_torque.shtml (scroll down a bit) Quote:
|
#15
|
||||
|
||||
Here is a handy tool. And your 90 degree theory works out too. http://cncexpo.com/TorqueAdapter.aspx
__________________
2018 EC 300 |
#16
|
|||
|
|||
My 2000 250 had 14 nuts on the outside and 13 either side of the power valve flappers so just check they are all the same size..
|
#17
|
||||
|
||||
http://www.motionpro.com/motorcycle/partno/08-0380/
http://www.motionpro.com/motorcycle/partno/08-0134/ All your motion pro dreams come true
__________________
Oz Current. 2015 ec300r estart, 98 RM 125 2013 Ec300r 2011 Ec300e 2009 Husky TE310 1982 XR500 Honda 1981 KE100 Kawasaki 1978 GT80 Yamaha |
#18
|
|||
|
|||
I must admit I never worry about torque values. Little bolts get tightened with a 1/4 drive, medium with a 3/8 or box wrench, big ones 1/2 drive or as tight as I can get with the big box wrench. I am happy if I remember to tighten all of them.
|
#19
|
||||
|
||||
Thats my theory too. The right tool usually gets you around the right figure. I'm not overly heavy handed (read weak as piss) so generally end up a little under the torque spec.
I still have all the tools for the more important things though.. 4T engine internals! |
#20
|
||||
|
||||
Theres a video somewhere on the site about an Aussie guy giving an instructional video on how to change the oil and filter on a road bike. After many humorous mechanic 'techniques' he says something along the lines of ' tighten it to, "its not going to fall out" Nm of torque'.
EDIT found it http://www.youtube.com/watch?v=Ft1Ik...layer_embedded |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2010 300 Cylinder Base Gasket Question | coopernicus | Enduro Engine - 2 stroke | 12 | 06-22-2011 09:31 PM |
torquing cylinder base nuts.... | stainlesscycle | Enduro Engine - 2 stroke | 17 | 03-08-2010 06:42 AM |
Front brakes driving me nuts | brains | Enduro Chassis & Body | 11 | 07-03-2009 03:49 PM |
'05 seat base | Loosenut | General Discussions & Announcements | 0 | 07-11-2008 12:02 PM |
Base gasket | Ud_luz | Enduro Engine - 2 stroke | 21 | 05-09-2008 07:38 AM |