#11
|
||||
|
||||
No guru mate, and you blokes are still jetting these bikes yourselves. All I've done is a bit of trial and error and passed on my findings.
|
#12
|
||||
|
||||
and we appreicate it....
__________________
broken down over 60 slow rider.. |
#13
|
||||
|
||||
No worres J. Edman, let us know how you get along or if you need any other help dialling it in. How good is that vid of Natos.
|
#14
|
|||
|
|||
Located in Arkansas.
Temp been around 90-100 degrees F. Sea level. Porb 50-70% humidity. I think I will first try 42 pilot/NEDJ and prob 172 or 175 main. I'm not sure air screw. I'm guessing 1.5-2 turns out. I will also lower float 2 mm while i'm in there as suggested by Jakobi. Any thing else? |
#15
|
||||
|
||||
Sounds good to me! Start in clip #3 but with those temps I wouldn't be surprised if you end up lifting the clip to #2.
I got a pm from twowheels and he has been running 40 NEDW#2 with 90F and close to 100% humidity. I think he's going to try a NEDJ as the bottom is a bit fluffy. MJC and myself have found the J works well in the 300's. The W is a better choice for the 250 as it gives a bit more torque off idle. |
#16
|
|||
|
|||
I'll let you all know how it goes. I hope to have everything before this weekend.
Thanks Again! Ed |
#17
|
||||
|
||||
Edman, I'm in Arkansas also and have the ASII on my new to me 2010. I'll pull carb when I get a chance to get #s for you. Mine starts well, idles well and runs awesome. It does have the squish set though and that can be a huge help. Where you located?
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#18
|
||||
|
||||
I'll be keen to hear what they've jetted your bike with too Fred. Sounds like you're loving the new ride!
|
#19
|
||||
|
||||
OOO Yeeaahh!!
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#20
|
|||
|
|||
I am in Hot Springs. Fred I would be interested to see how yours is jetted. I will probably check into the squish in the winter. It suppose to really make a difference with jetting from what I have read.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Jetting ? | rootsnrocks | Enduro Intake/Carburetion - 2 stroke | 38 | 03-12-2013 02:22 AM |
EC 300 Jetting | Casey97 | Canada | 6 | 05-05-2011 11:52 PM |
GG jetting | Gasgasogeros | Enduro Intake/Carburetion - 2 stroke | 0 | 02-21-2011 06:39 AM |
06 300 jetting | fury1 | Enduro Intake/Carburetion - 2 stroke | 1 | 07-31-2007 06:37 AM |
02 ec 250 jetting help | crem55 | Enduro Intake/Carburetion - 2 stroke | 9 | 07-12-2007 01:44 PM |