|
Enduro Suspension Tuning & maintenance of Enduro forks, shocks, etc |
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
also italian husqvarna used 48 cc what forks are the swm s using also ask on the usa gg f book page richard willson
|
#12
|
||||
|
||||
Quote:
The typical inner and outer bushings for the 48mm Zoke can be found in the correct sizes quite easily. The bushing for the ICS piston doesn't really have any cross overs and given that they were a fork that were used on the Gassers and Betas for a few years (with both brands now using other brands; KYB and Sachs), they could be hard to come by. |
#13
|
|||
|
|||
Can you measure (in mm) the sizes? I have my crap Sachs CC forks of a Beta to bits and the piston looks very similar. If the sizes are the same you can get the bushings from a Beta dealer. PM me I'll get my callipers out in the mean time.
|
#14
|
|||
|
|||
Here are some pics
Sent from my iPhone using Tapatalk |
#15
|
|||
|
|||
Need to find Inner cartridge bushings-48mm marzocchi’s
These are the 2nd set of bushings(35151) that I ordered. The 36mm (36151) bushings were way to loose. I wonder if they bushings are getting compressed to the point that the end gap is closing. Sent from my iPhone using Tapatalk |
#16
|
||||
|
||||
Quote:
make a holder for the bushing. (a cylinder of slightly lower ID than the bush OD), puth the holder in the lathe and the bushing in the holder. As you want to remove only a slight amount, use e.g. 320 paper and lightly remove some material. Place the bushing on the piston, measure O/D. Repeat as needed. I haven't tried to do it, but that would be my approach.
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#17
|
|||
|
|||
I do have access to a lathe. I can give it a try. Thanks
Sent from my iPhone using Tapatalk |
#18
|
|||
|
|||
iv just asked on gg riders fb for you . bit of a long shot what about there mountain bike forks id be surprised if marzocchi had them made specially
|
#19
|
|||
|
|||
as i expected richard wilson usa has a set also zipty racing n america has them rw also has softer ics springs
|
#20
|
|||
|
|||
I pm'd you with the sizes of the Beta Sachs CC cartridge bushes. I think they might fit. Only thing is that you might have to adjust the end gap a bit.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
PFP adjuster on 48mm Marzocchi’s | rvangeel | Enduro Suspension | 2 | 03-18-2018 03:26 AM |
Marzocchi 48 Cartridge Problem | fixmare | Enduro Suspension | 30 | 09-11-2017 05:38 AM |
Fork Oil Volume for 2013 Shiver 48mm Closed Cartridge | scov | Enduro Suspension | 3 | 04-21-2013 02:04 AM |
Sachs 48mm Bushings | Jakobi | Enduro Suspension | 9 | 06-19-2012 07:18 PM |