|
Enduro Product Announcements Announce new gasgas enduro products here - Vendors Welcome... |
|
Thread Tools | Display Modes |
#11
|
||||
|
||||
Nice big pic...It looks nice.
Would like to see some more from different angles and without the shrouds but it's (finally) the only choice in town if you want a slightly bigger tank. Come on Mark and Steve, lets get those pics up with the new tank!
__________________
07 EC 300 (under 500 miles, selling soon) 97 KTM 250 EXC (sold) 2016 Trek Remedy 29er |
#12
|
|||
|
|||
Has anyone had a chance to check fit with a steering stabilizer? I'm running the GPR V-4 on my 300 and my son has the Motosportz on his 250.
__________________
Frank Staley President in Exile-Arizona Trail Riders "You live more in 5 minutes on a motorcycle than some people do in a lifetime" - B. Munro |
#13
|
||||
|
||||
Quote:
Thanks Mark |
#14
|
|||
|
|||
Quote:
OK, back on topic. I really want one of these tanks, has anybody checked fitment with the aforementioned steering stabilizers???
__________________
Frank Staley President in Exile-Arizona Trail Riders "You live more in 5 minutes on a motorcycle than some people do in a lifetime" - B. Munro |
#15
|
||||
|
||||
Thanks mate.
Cheers Mark |
#16
|
|||
|
|||
Berkyboy? Wannabe? Any input here? I'm sure someone considered this before the tank was finalized. I need 2 of them, just want to make sure they will work with the stabilizers first.
Thanks
__________________
Frank Staley President in Exile-Arizona Trail Riders "You live more in 5 minutes on a motorcycle than some people do in a lifetime" - B. Munro |
#17
|
||||
|
||||
Clarke Tank Fitment
OK, I'll try to keep this short and precise. Keep in mind I'm not the photographer, Steve is so could my pics be blury? Yep, probably.
The new tank WILL fit the 2010 exactly with the exception of one thing. Clarke designed the new tank with two "L" brackets that screw into the tank underneath the frame. These brackets are to hold the tank in place instead of the bolt up top by the clamps and the tank strap at the back. Works great on the 07-09, BUT!!!! In 2010 GasGas's new frame design has the ignition coil going vertically on the right side instead of all the other years when it was horizontal. This switch has made the bracket position directly behind the wires and coil on the 2010. With some more patience, you maybe able to attache behind coil...with more patience. I attached the left side and with the seat secure, radiator shrouds secure, the tank isn't going to jump around. All bolts lined right up, but the top of the shrouds are pushed out from the extra tank and the tabs won't reach to the radaitor (this is on 07-2010). I am sure with a heat gun you can form your shrouds to a cleaner fit. Also, there is only 3 cm of room between the tank and the weld on the top of the frame/steering colum. About 3 1/2 cm from tank to steering stem and less than 3 from tank to dust cap. Tank is 3.2, haven't measured to find out yet exact capacity, but a nice tank and a clean fit actually with directions on the "L" brackets, Clarke's own larger bolts are phillips like they have been in the past but the bolts for the "L" brackets are 10mm hex head. Pics are in the members gallery! Will try to fit a 125 this weekend, keep you posted. Next up, EXP Rekluse clutch! Had a great conversation with Rekluse today....
__________________
Mark Berg |
#18
|
||||
|
||||
Clarke makes such nice tanks. I have always been very satisfied with every Clarke Tank I have ever purchased (6 different bikes and counting.)
Jeff Webmaster GasGas Riders Club |
#19
|
||||
|
||||
Thanks for the photos Mark.
It looks like you can use the '07-'09 radiator shrouds on the '01 bikes. This may allow for a cleaner fit. |
#20
|
||||
|
||||
For the shrouds, add an LTR GP brace through the top mount grommets. Now get a vibration isolator used on the lower pipe mount. Thread the M6 stud into the LTR brace. Now, cut the tit off the shroud and drill an M6 clearance hole to mathh the hole in the isolator. Use a 10mm M6 bolt and fender washer to retain the shroud. You may have to add washers behind the isolator to adjust fit.
You can also attach the isolator to other rad guards/braces for the same result. I've been doing this on my last two bikes with the stock tank and it makes the shrouds much more durable and less likely to be torn off up top. The isolator will flex and not crack the shroud in minor impacts. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
4t oversize tank on a 2t? | wence | Enduro Chassis & Body | 1 | 07-08-2010 12:29 PM |
Oversize tank for the new bikes | Skidad | Enduro Engine - 2 stroke | 8 | 10-22-2008 12:28 PM |
Oversize Tank for 07' 2 strokes | Roy Salmon | Enduro Chassis & Body | 2 | 01-26-2007 06:06 PM |