|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#21
|
||||
|
||||
http://www.mikesxs.net/products-82.html#products
warning: i am not 100% sure these fit 36mm-38mm pwk. they do fit 32mm pwk. i know the float needle does not. at $3.00 it was worth the risk..
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#22
|
||||
|
||||
I made one out of a sheet of heavy paper. What a PITA. I had the right size o-ring in my bag of o-rings.
__________________
04 Montesa 315R, 07 EC300, 21 KTM Erzberg 300, 21 Sherco 300 SEF-F, 23 KTM 690, 23 Rieju Mr Pro 300 |
#23
|
||||
|
||||
There's a thread around here with pictures of everything but I couldn't find it. It's very obvious how things are put together when you take it apart.
__________________
04 Montesa 315R, 07 EC300, 21 KTM Erzberg 300, 21 Sherco 300 SEF-F, 23 KTM 690, 23 Rieju Mr Pro 300 |
#24
|
||||
|
||||
Quote:
I asked my bud to take his carb off and drop it off so I could take the jet block out and check it. We were talking about this the other day...and because he's a beginner and new to the sport he didn't know that his bike was running like crap...he thought that was just how they are. So, he's been riding the bike like this for almost 2 years, none of us knew until I took his bike for a good spin....it runs like s*#t. So, I am on a mission to get it straightened out. When I ran across your post, I thought that sounds just like the issue my buddy is having. We'll see In any case, thanks for posting it !!! |
#25
|
||||
|
||||
Could you use Permatex or Yamabond in place of a gasket or is it too critical? orings are easy to source.
|
#26
|
||||
|
||||
it's pretty critical, there are a lot of tiny passages....
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#27
|
||||
|
||||
This might be totally non applicable, BUT I have noticed that when I adjust the idle air screw, it effects the spark plug. Sometimes it just fouls it out and the bike dies. Sometimes, what is even worse then a dead bike, is it starts running very erratic and strange, almost to the point you think there are some major issues.
Again, dont know if this helps, but thought it might. gasgasdreamer
__________________
2002 Husberg FE650e 2006 GasGas EC300 2014 Sherco SER300 2014 Beta Evo Factory 300 |
#28
|
||||
|
||||
Another thought.... Is your idle adjustment screw the plastic one or a brass one?
I had the plastic idle screw get hammered flat on one side from the slide being dropped on it over time. Or maybe someone in camp kept snapping the throttle when I was not looking....?!?!?? The bike would barely idle. If you turn the screw maybe 1/4 turn it would rev up big time. Keep turning for a full turn and it would barely idle again. I replaced the screw and problem fixed. Worth the 5 min. to check. Jeff |
#29
|
||||
|
||||
Where did you get a brass screw?
__________________
04 Montesa 315R, 07 EC300, 21 KTM Erzberg 300, 21 Sherco 300 SEF-F, 23 KTM 690, 23 Rieju Mr Pro 300 |
#30
|
||||
|
||||
Hmmmm... I think I replaced it with another plastic one, but, I can't
remember for sure... It has been a few years since this happened. I think a brass one may be available from Sudco or maybe as an OEM part from another bike that uses the Keihein carb. I think my KDX200 uses the same slide screw..?!?!?? I'd have the pull them both to be sure. Jeff |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to set float level. Revisited. | gasgasman | Enduro Intake/Carburetion - 2 stroke | 48 | 11-10-2018 05:11 AM |
Help 04 ec300 wont idle | nmhinton | Enduro Intake/Carburetion - 2 stroke | 18 | 08-31-2011 10:51 AM |
Rear wheel spacers revisited. | Ud_luz | Enduro Chassis & Body | 9 | 09-13-2010 08:01 PM |
can,t get idle up | geno | Enduro Intake/Carburetion - 2 stroke | 1 | 04-18-2010 08:49 PM |
2001 EC300 won't idle - can't get jetting right | bexi | Enduro Intake/Carburetion - 2 stroke | 16 | 03-04-2010 10:30 PM |