#21
|
|||
|
|||
Tear Down Updates
Well things are moving along. the bottom motor bolt was tough to take off. I had to put the torch on it twice and pound it out with a mini sledge. It was very rusted and bent.
Here is the bottom end on the workbench. The water pump cover came off without a problem. It looks like new inside. The impeller looks perfect as well.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#22
|
|||
|
|||
I don't think the clutch cover has ever been off the bike. small dent in lower cover, looks like from the rear brake pedal when someone tipped over.
Some sludge in the bottom of the clutch cover, I rinsed this all out with some brake cleaner. The clutch basket and plates look original and the clutch basket has never been off the bike. just a very small amount of grooving on the clutch basket. But the steel plates have rusted into the fiber plates.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#23
|
|||
|
|||
One Problem
I need help on one problem. I can't get the primary gear nut on the crank loose. I read some threads that said Suzuki put a high strength locker on this nut and it was only removable with heat. Some thought the bolt was a left hand thread because it was so hard to remove, but other said it was right hand thread but it took a lot of heat. I put PB blaster and the torch on the nut, then put my 1200 pound Milwaukee Impact Wrench on it, it didn't move the nut at all and it rounded the edge of the nut but I stopped immediately and I straightened the damage with a file.
I could use my 3/4 breaker bar with a 3/4 inch 19mm socket. Any suggestions?
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#24
|
|||
|
|||
And the nut came right off the stator. I have 6 flywheel pullers and none of them fit this design which has the two locations to thread into the bolt holes. Any body have specific puller model to recommend?
Any suggestions?
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar Last edited by Moto7man; 04-02-2018 at 02:29 PM. Reason: grammer |
#25
|
|||
|
|||
The clutch basket looks fabulous with no indication that it has ever been removed from the bike.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#26
|
||||
|
||||
Quote:
Maybe try Thumpertalk in the Suzuki 2 stroke section as well?
__________________
Phil (New bike pending...) |
#27
|
|||
|
|||
Uh.Well
Its a Suzuki and their is a high probability that nut is reverse threads.Left hand. Get out now while you still can. Pretend you never saw it. Quietly make it go away. |
#28
|
|||
|
|||
Quote:
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#29
|
|||
|
|||
LOL, you are cracking me up, you may be right......
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#30
|
|||
|
|||
Does anyone know the original blue paint code or the blue powdercoat code for the frame on this bike?
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
94 CR 250 Ground Up Restoration IMS Wide Ratio Transmission Issue | Moto7man | All Other Bikes... | 146 | 01-28-2018 05:57 PM |
1994 CR 250 Restoration featured on Dirt Bike Magazine Webpage | Moto7man | Pictures & Videos | 8 | 10-28-2017 09:12 AM |
Gas Gas Contact Jt 25 95 Restoration And Help | Eyetech | General Discussions & Announcements | 1 | 03-18-2016 03:33 PM |
2001 XC200 Restoration Project | Lincolnlock | Enduro Engine - 2 stroke | 19 | 04-22-2014 03:42 PM |
My Stomping ground | swazi_matt | Ride Reports | 10 | 03-02-2011 09:35 AM |