|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
brembo ktm front brake conversion
Hi all
i have a 12 ec300 factory, im not happy with the factory nissin front brake. has any one fitted a front ktm brembo set up? Or even just changed the master cylinder to a brembo unit? Feedback please i have tryed to get my set up good but it has now never been better but im still not happy... i have come from ktm and their units are wicked! cheers |
#2
|
||||
|
||||
Quote:
Have you bled the brake? what condition are the pads in, try some 'sintered' ones for more bite. What about the brake line? swap them out for braided ones. I have 98 ec250 with brembo's fitted which I stripped down and rebuilt using all of the above I have suggested to you They are excellent brakes,however from experience the parts are stupidy expensive I think I paid 9 pounds for a rubber slider cover and I needed 2 !! |
#3
|
|||
|
|||
hi savage sausage
thanks for your input but.. gp bikes dont go 315mph and there braking set ups are unrelated to our dirt bikes for many obvious reasons have tried many pad types, brands, sintered expensive pads etc.. My machine is running a braided line your year runs brembo??? is that on a marzocchi forks? Cheers |
#4
|
||||
|
||||
sorry typo on the 315mph I meant 215mph.
my point regarding that was ,they are as good as each other. no it's a six days models so runs paioli's |
#5
|
|||
|
|||
I've used a couple of different calipers and master cylinders on my supermoto and the fork mount is the same as ktm 95mm
|
#6
|
||||
|
||||
I tried a Brembo front caliper and master cylinder on my 13 Gas Gas and the mount for the brake was juuuust a hair off, although the bolt holes did line up (using a 2007 KTM 250 XCFW front brake setup). The stock rotor grazed the inside of the caliper. So I never was able to tell if it made a difference because I didn't want to take a chance on a mishap and didn't want to fuss with it anymore. It's funny because my 13 had terrible front brakes and no amount of bleeding, changing pads, etc. seemed to improve it. My 14 has great brakes, so I'm really not sure what the difference is.
|
#7
|
||||
|
||||
Perhaps because GG was at the bottom of the vendor list and were using factory-seconds? I certainly believe that was the case with the Keihin carbs on the 2012 model year.
|
#8
|
|||
|
|||
phoenix! thanks for the info.. much appreciated, yep the nissin setup is crap.. this would have to be the let down on my machine. i have tryed and tryed to get it good with little improvement. cheers
|
#9
|
|||
|
|||
capz85.. what was your best combination?
|
#10
|
|||
|
|||
Quote:
cheers |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Brembo Caliper SM Gassers | stian | Enduro Chassis & Body | 4 | 08-04-2014 12:38 PM |
Front Brake Mod | GasGas | Enduro Chassis & Body | 3 | 09-19-2013 06:33 PM |
20mm thread (04-early 06) front axle nut conversion | Keg | Enduro Product Announcements | 7 | 04-14-2013 06:33 AM |
Brembo brake light switch | savage sausage | Enduro Electrical & Wiring | 6 | 09-13-2012 12:11 AM |
Brembo Brake Parts | savage sausage | General Discussions & Announcements | 4 | 04-17-2012 04:47 PM |