Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > Other Bikes... > All Other Bikes...

All Other Bikes... KTM, Husky, VOR, Husaberg & Hondayamazuki...


Reply
 
Thread Tools Display Modes
  #1  
Old 04-21-2007, 01:35 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default New BMW off road 450



Not bad looking.
Engine exposed a little too much.


Reply With Quote


  #2  
Old 04-21-2007, 09:54 PM
Dave Dave is offline
Senior Member
 
Join Date: Jul 2006
Location: StL, MO
Posts: 392
Default

EFI, linkless Ohlins, primary clutch, tank under the seat, check out the swing arm pivot location. BMW certainly went their own way with this one.
Reply With Quote
  #3  
Old 04-22-2007, 05:50 AM
wise old man wise old man is offline
Member
 
Join Date: Aug 2006
Posts: 25
Default

Yes very BMW and yes those engine cases must be made of some super strong space age material.
Reply With Quote
  #4  
Old 04-22-2007, 03:17 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

Quote:
EFI, linkless Ohlins, primary clutch, tank under the seat, check out the swing arm pivot location. BMW certainly went their own way with this one.

Or the way of a small bicycle company from PA.
Reply With Quote
  #5  
Old 04-22-2007, 09:49 PM
jeffd jeffd is offline
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Portland, Oregon, USA
Posts: 417
Default

http://www.youtube.com/watch?v=0ZcqEqUzIAY

...Hanging out in the husqvarna pits?

jeff
Reply With Quote
  #6  
Old 04-22-2007, 10:03 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

Some very innovative stuff, with the $$ to back up development. I bet it makes an FSR 450 seem cheap($$) by comparison.

If it comes to Hancock, NY I'll get some photos.
Reply With Quote
  #7  
Old 04-24-2007, 06:38 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

Close up of motor.
The clutch is driven directly off the crank shaft.
Looks like a closed loop* fuel injection system, as opposed to Gas Gas' old school speed density* setup.




*Closed Loop-uses an oxygen sensor and air flow sensor to determine fuel delivery.
*Speed density- uses throttle position sensor to determine fuel/air ratios based off predetermined parameters matrix.
Reply With Quote
  #8  
Old 04-24-2007, 09:11 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

Girard, your an auto tech. My buddy who is as well tells me, along with the Optimum guys who did Cannondale's system, that closed loop is great but the O2 sensor needs an air referance port that would be too hard to keep clean enough on a dirt bike. He said a lot of 4x4 trucks that see mud bogs come in with trouble and are found to be dirty sensors. Thoughts?

All that tech and a cable clutch?

Is that really PDS or possibly a type of top mount linkage? hard to see for sure.
Reply With Quote
  #9  
Old 04-24-2007, 09:22 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

Yeah, you're right about the O2 sensors.

The automotive 02 sensors vent through the sheath that covers the wires going into the sensor body.
I imagine water would get down into that sheath.

The clutch seems really small.
Being driven by the crankshaft, I think it would be spinning too fast to keep the clutch plates lubricated.
They probably had to go with a cable clutch because there was no room for the hydrualic set up,would make the engine too wide.
Reply With Quote
  #10  
Old 04-24-2007, 09:37 PM
gasgasman's Avatar
gasgasman gasgasman is offline
Super Moderator
 
Join Date: Jul 2006
Location: Pearland Texas
Posts: 4,594
Default

Found this:

Quote:
-------------------------------------------------------
BMW patents new chain drive

01 March 2007
BMW has filed a patent for a completely new motorcycle concept that would allow extreme suspension travel while minimising the amount of slack needed in a drive chain, belt or shaft.



A conventional motorcycle needs free play in the drive chain to allow for movement in the rear suspension. On an off-road motorcycle this becomes even more important, and with suspension travel of 300mm the chain needs about 70mm free play at the tightest point. Such a slack chain results in power losses and high wear rates through friction, and would need a chain guide to stop the chain jumping off the sprockets.



The clutch is usually mounted on the gearbox output shaft on a motorcycle, but inventor Markis Theobald, in Patent Number EP1743832 filed on behalf of Bayerische Motoren Werke AG (DE) on 17 January 2007 proposes mounting it on the engine crankshaft. The gearbox output shaft can then be co-axial with the swingarm pivot, so that chain tension is always maintained without unwanted slack.



An added advantage of the BMW design is that because the clutch turns at engine speed instead of the usual half engine speed of a conventionally mounted clutch, a smaller, lighter unit can be used.
-------------------------------------------------------------
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
GG Fantasy Off Road Team? gasgasman General Discussions & Announcements 16 08-25-2010 07:20 AM
300ec on the road? firffighter Enduro Engine - 2 stroke 2 10-05-2009 05:00 AM
Off Road Racer's Corner???? Bandit9 Suggestion Box 7 02-03-2008 06:18 PM
05 300ec for the road hlrembe Enduro Electrical & Wiring 8 01-04-2008 02:57 PM
Need Help to Register fsr 450 for road use please kaw1965 General Discussions & Announcements 3 07-31-2007 05:09 PM




All times are GMT -5. The time now is 12:09 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org