Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 05-16-2018, 07:16 PM
rvktm rvktm is offline
Senior Member
 
Join Date: Apr 2014
Posts: 128
Default clutch rivet size help and will it fit my 013

a while back i brought a clutch basket with gear of a gg 250 it has a date stamp of 08 on the basket all the rivets have bean drilled out any one no the size of the rivet , the hole size is 4.2 can i use 1/8 mild steel rivet .also will it fit my 013 300 thanks


Reply With Quote


  #2  
Old 05-17-2018, 06:47 AM
Zman's Avatar
Zman Zman is offline
Platinum Level Site Supporter
 
Join Date: Apr 2010
Location: Burbs of Chicago
Posts: 1,818
Default

I believe standard pop rivets will not work. I would tap the holes and use screws with Loctite like everyone does for aftermarket baskets.
Reply With Quote
  #3  
Old 05-17-2018, 10:18 AM
rvktm rvktm is offline
Senior Member
 
Join Date: Apr 2014
Posts: 128
Default

sorry forgot to say its a gg std basket
Reply With Quote
  #4  
Old 05-17-2018, 01:22 PM
Zman's Avatar
Zman Zman is offline
Platinum Level Site Supporter
 
Join Date: Apr 2010
Location: Burbs of Chicago
Posts: 1,818
Default

I think it is still common for people to tap threads into the stock basket and use bolts to put it back together.
Reply With Quote
  #5  
Old 05-23-2018, 07:07 AM
Thompo Thompo is offline
Senior Member
 
Join Date: Aug 2017
Location: Northern Ireland
Posts: 101
Default

I used "Reaper Rivets" from a farm shop on a husky I was restoring. I think they are used for holding flail blades onto something, close to 5mm Dia, 20mm long and just cut them down to right length.

I struggled to find the right Dia/length/CSK combination anywhere. Rivets are mainly an aviation thing these days 100/130? csk angle.

5/32 would be a better fit for 4.2mm hole, ideally you would want a 4mm metric rivet. Remember to get a rivet long enough to allow proper forming of the head, typically stack thickness +1.5x dia.
There should enough material to open up the hole a little to allow for a bigger rivet or re-cut the csk to suit something you can get.

EDIT#Never been inside the gasgas clutch so not sure how the rivets are....
Reply With Quote
  #6  
Old 05-23-2018, 12:35 PM
rvktm rvktm is offline
Senior Member
 
Join Date: Apr 2014
Posts: 128
Default

iv found 1/8 cks rivets on uk ebay only 3.00 uk for 10
Reply With Quote
  #7  
Old 05-23-2018, 04:11 PM
Zman's Avatar
Zman Zman is offline
Platinum Level Site Supporter
 
Join Date: Apr 2010
Location: Burbs of Chicago
Posts: 1,818
Default

We're the rivets Aluminum or stainless steel? Please let us know how it works out.
Reply With Quote
  #8  
Old 05-25-2018, 01:47 AM
Thompo Thompo is offline
Senior Member
 
Join Date: Aug 2017
Location: Northern Ireland
Posts: 101
Default

The rivets I drilled out of the husky were steel.

I replaced them with a steel rivet.

I used something like this http://www.sapphireproducts.co.uk/641t9.htm
Reply With Quote
  #9  
Old 05-25-2018, 08:52 AM
robicon robicon is offline
Senior Member
 
Join Date: Mar 2012
Posts: 152
Default

I just had this issue I drilled out my only to find the new one was not correct. I did want to wait for a new one. I used stainless rivets and had to peen them for clearance. No problems
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Clutch fiber and steel size??? 2011 GG EC 300 jb250xcf Enduro Engine - 2 stroke 2 11-05-2016 05:16 AM
Magura clutch MC size on 2012 XC300? Bandit9 Enduro Chassis & Body 2 11-05-2013 07:01 AM
Clutch lever doesnt release clutch as soon as motor starts cal_tony Enduro Engine 4 stroke (including EFI & Exhaust) 5 05-19-2012 08:59 AM
Masterlink...Rivet or Clip Rick Enduro Chassis & Body 9 11-27-2009 07:17 PM




All times are GMT -5. The time now is 05:22 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org