|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
newbie.....03 EC250???
Great looking site guys.....so here's where you earn your keep.....
Been riding off road for years, mostly big bore husky's and vintage MX on my CZ and RM but really need a modern/reliable/easy trailbike......so, I'm looking at an 03 EC250 ........I've known of GAS GAS quality for years.......why should I buy this bike? What makes the power tractable for a 250? what's special about the motor for durability? what about pivot points, taper bearings or ?? electrical problems later?? what's the bad?? Give it to me straight - I know you will !!! thanks for the info Rich |
#2
|
|||
|
|||
opinions......?? info is appreciated in helping me make this decision.
|
#3
|
||||
|
||||
I had an '03 EC250. More tame stock than my '00 or '07 due to the CDI IMO. If you want a smooth 250 this is it. WP forks/Ohlins can be tuned to your liking. The linkage is the same as the new bikes and if it has been maintained well no problems. GGs trade a couple lbs for a rugged motor that is quite bulletproof. Thick cases, good cooling system, etc. The bike bottomed out in price awhile ago so unless its a wreck its a lot of bike for the $$.
|
#4
|
||||
|
||||
as gmp said.. they are awesome bikes.. still have my 01 and am getting a newer one soon..no problems with mine in three years or so..
__________________
broken down over 60 slow rider.. |
#5
|
|||
|
|||
thank you - it does have Ohlins front/rear with some nice LTR protection, new fmf fatty also. the owner was early 40's and everything seems tight on it, I believe maint was kept up.
question - how's the powerband....broad with some grunt?? I know it's a still a 250 but I don't want a high rever for horsepower. And.....will it overheat doing miles of tight single track -1st gear stuff?? |
#6
|
||||
|
||||
i had a 250 and the 300 i have now... it does not have the grunt of a 300, but nothing else does either.. it is respectible IMO.. more so than a jap 250 2 smoke 250... i have had mine over heat once in three years.. and the 6 speed and hyd clutch are just cheating... what are you riding now ?
ohlins front and rear and ltr stuff... go buy it..
__________________
broken down over 60 slow rider.. |
#7
|
|||
|
|||
Quote:
I have all vintage - 83 Husky 430WR (bought new - trial ride and vintage MX) just overhauled and has great power - but I'll getting to old to kick start it all day in the woods after 40-50 miles 77 Suzuki RM250 - vintage mx in the NW......great mx power, not a woods bike 74 CZ 400 - big bore 4spd....tons of torque - all mx |
#8
|
||||
|
||||
Quote:
jay..
__________________
broken down over 60 slow rider.. |
#9
|
|||
|
|||
alright - I'll go call the shop and talk a deal.......I'll let you know.......
|
#10
|
||||
|
||||
Picked up my first Gasgas last year ('03 EC250), after owning a ton of different off road bikes. Amazing bike, easy to ride, great low-end and about the best single track bike out there.
I sold it to pick up a newer Gasgas and ended up with an '05 EC300 that had really low hours. To be honest, there is not much difference in low end on the 250 vs 300. Both are great. The 250 has a bit more aggressive bite to it, but not bad and again, works great for tight woods. Great bikes and you get a ton of bike for the $. I've owned 'em all and Gasgas is tops in my book. BTW, would you happen to be looking at the bike at Tasky's in WA? |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Newbie bought 2004 EC250 - need help with parts | stuckinatree | Enduro Engine - 2 stroke | 13 | 11-09-2010 09:14 AM |
Forum newbie (ec250) | gregtenerife | General Discussions & Announcements | 3 | 03-12-2010 08:19 AM |
Newbie | jarvy | Enduro Engine 4 stroke (including EFI & Exhaust) | 0 | 08-17-2008 02:19 PM |
Newbie here | c-152 | General Discussions & Announcements | 2 | 04-03-2008 08:59 AM |
Help a Newbie Out! | chambersc | General Discussions & Announcements | 7 | 10-22-2007 03:21 PM |