|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
What position do you run your bars?
Trying to set this 08 300 up for next weeks race......
I am 6' 225lbs.... where do you guys run your bars....looks like the bars are in the rear hole.....think I need the front hole.....do the risers flip around like KTM ones?
__________________
2008 EC300 Rekluse |
#2
|
||||
|
||||
i'm 5'11" 190lbs - on my 00 i had an adjustable triple tree (checkpoint machine) - i ran them directly above the center of the fork tubes. on the 07 i just got, i'm a little confused. it had a brp submount riser on it, which i removed. it revealed 2 sets of holes. the rearward ones (10mm hole) and the middle ones - which would be close to what i had previously (12mm hole). since the bar clamps i have are set up for 10mm hole and don't flip around (from a 99), i put them in the rear. kinda feels a little cramped, but : turning seemed to be improved, and getting on the tank in corner entrances seems easier. also when climbing hills, i found myself pulling myself up by the bars instead of just standing with my legs. i bought some bushings from mcmaster (12mm to 10mm) and am gonna try the forward mount (maybe) for the race this weekend.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#3
|
|||
|
|||
let me know....
also anyone use a seat bump? this thing slides me right off the rear.... any measurements you use? just one bump or the whole rear of the seat?
__________________
2008 EC300 Rekluse |
#4
|
||||
|
||||
i put a bump in on my 2000. maybe 3/4" high. just one that kept me in knowing where i should be..... doesn't stop sliding, but you'll feel it easily, and it's a reminder to get up on the tank..
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#5
|
|||
|
|||
crap....guess where i have been riding 125s, 200s and 250 4t lately....this thing pulls right out from under me.....
__________________
2008 EC300 Rekluse |
#6
|
||||
|
||||
hah, throttle control. can't do the 125 thing and just run it like a weedeater!
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#7
|
|||
|
|||
all about throttle control....just seeems like I am sitting on glass....need a bump or hump or grip tape on shrouds or something
__________________
2008 EC300 Rekluse |
#8
|
||||
|
||||
Bluegrass,
Short shift it and ride it like a 4T and it won't try to ride out from under you. It will feel like you're going slow but you won't be. You can carry so much corner speed! Clay |
#9
|
|||
|
|||
now i do ride it like a 4 st....but getting use to it....
thing huals butt in the open although its gets some headshake....feels like i need a taller seat too....but i like the tiny feel too....
__________________
2008 EC300 Rekluse |
#10
|
|||
|
|||
I run my 2010 in the front holes. I think the clamps are also offset and can be rotated. I found the front holes just felt more natural to me
__________________
2003 txt250 Pro 2013 Ossa 280i |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rear brake position | Lildawg | Enduro Chassis & Body | 18 | 06-15-2011 11:17 PM |
Changing needle position? | EcEvan03 | Enduro Intake/Carburetion - 2 stroke | 6 | 04-27-2011 03:09 PM |
Handlebar mounting position | bchatt | Enduro Chassis & Body | 8 | 10-14-2010 05:34 AM |
neddle position Question | biggstr6 | Enduro Intake/Carburetion - 2 stroke | 8 | 05-12-2010 10:26 AM |
Clip position ? | thingymijig | Enduro Intake/Carburetion - 2 stroke | 3 | 03-01-2007 04:57 AM |