Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 02-24-2011, 10:11 AM
blanc blanc is offline
Senior Member
 
Join Date: Oct 2010
Posts: 178
Default Powervalve cover on the 200?

Does the powervalve cover make a difference on the 200?


Reply With Quote


  #2  
Old 02-24-2011, 11:27 AM
Rick's Avatar
Rick Rick is offline
Senior Member
 
Join Date: Aug 2006
Location: Lodi, Ca
Posts: 1,930
Default

I have one on my 200 now, did not for many years. I really can't tell a difference.......I've done back to back with and without the cover and I think the reason why is my I really can't feel a difference is my pipe which is a Messico pipe has been modified.

My 200 run strong anyway, due to some of the mods that has been done to it, so I might not have been the best person to responed with the info your looking for.

Thanks
__________________
Rick
99 EC 200
06 RM 250
AMA D36
375X
OTHG
375S

***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals
Reply With Quote
  #3  
Old 02-24-2011, 12:30 PM
stainlesscycle's Avatar
stainlesscycle stainlesscycle is offline
Site Sponsor
 
Join Date: Jun 2009
Location: morgantown, wv
Posts: 1,608
Default

i don't know either. i have one on mine, but it's got so many mods going on (like rick's) 'cept i have doma pipe... i've not tried without it..
__________________
07 ec300
was 00 xc200 now a 00 xc300. now parting out.
99 ec300 (now a pile of parts which are for sale)

Stainless Cycle - Motorcycle Bolt Kits
www.stainlesscycle.com
Reply With Quote
  #4  
Old 02-25-2011, 04:09 AM
blanc blanc is offline
Senior Member
 
Join Date: Oct 2010
Posts: 178
Default

Even with the 13 51 gearing and the map in sun mode Im not that happy with the power.Any suggestions to waken the low to mid range up? The bike needs major reving to go up hills etc
Reply With Quote
  #5  
Old 02-25-2011, 07:32 AM
noobi's Avatar
noobi noobi is offline
Senior Member
 
Join Date: Sep 2008
Location: New Zealand
Posts: 1,031
Default

Put the 2k2 flywheel on it. The 2k3, stock with wires exiting at 2pm, is too much flywheel, the 2k2 has a much smaller rotational inertia and effect, wires exit at 10am, it will make the bike much more free revving and will make the transition into the mid range faster. Thus more responsive.
I'v ridden 200s with the 2 different flywheels and the bike with the 2k2 was noticeably easier to ride aggressively as it was much more willing to rev from the bottom to mid range compared to the 2k3 which required healthy doses of clutch and throttle to get into the meaty mid range.
Reply With Quote
  #6  
Old 02-25-2011, 07:49 AM
stainlesscycle's Avatar
stainlesscycle stainlesscycle is offline
Site Sponsor
 
Join Date: Jun 2009
Location: morgantown, wv
Posts: 1,608
Default

definitely do the 2k2.

what pipe do you have?

if jetting is rich on the pilot, it'll be sluggish till it gets on the needle...
__________________
07 ec300
was 00 xc200 now a 00 xc300. now parting out.
99 ec300 (now a pile of parts which are for sale)

Stainless Cycle - Motorcycle Bolt Kits
www.stainlesscycle.com
Reply With Quote
  #7  
Old 02-25-2011, 12:43 PM
Rick's Avatar
Rick Rick is offline
Senior Member
 
Join Date: Aug 2006
Location: Lodi, Ca
Posts: 1,930
Default

Blac check your PM later on today for some idea's.
__________________
Rick
99 EC 200
06 RM 250
AMA D36
375X
OTHG
375S

***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals
Reply With Quote
  #8  
Old 02-28-2011, 04:46 AM
blanc blanc is offline
Senior Member
 
Join Date: Oct 2010
Posts: 178
Default

Thanks a mill all. Rick your PM should be turned into a sticky on 200 setup! What are vforce reeds like on the 200?
Reply With Quote
  #9  
Old 03-20-2011, 04:45 AM
bitoman bitoman is offline
Member
 
Join Date: May 2009
Location: Honolulu
Posts: 13
Default

Hi I would like to see a sticky for 200 set up also.Especially yours Rick I believe you have a 99?
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Oversize powervalve cover. Todd5774 Enduro Engine - 2 stroke 65 04-11-2011 12:43 PM
Adjustable powervalve cover darren Enduro Engine - 2 stroke 1 01-12-2009 05:27 PM
ltr powervalve cover moff747 Enduro Engine - 2 stroke 5 03-05-2008 01:24 PM
'03 200 Powervalve cover Bearman General Discussions & Announcements 9 01-01-2008 06:59 PM
LTR powervalve cover ejas General Discussions & Announcements 2 08-23-2007 08:09 AM




All times are GMT -5. The time now is 05:50 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org