|
Enduro Product Reviews Feedback & Comments on Products Tested |
|
Thread Tools | Display Modes |
#41
|
||||
|
||||
Trevor: What did you just say here? Go with the +1 1/2" GasGas non T3 or buy the KTM T3? Part numbers help
__________________
Steven Beane #275 PlusOnePerformance - Superior Service the World Over - Dearborn MI AMA District 14 (Michigan) Officer afterhourscycle.com Michigan's Beta and TM Race Headquarters |
#42
|
||||
|
||||
Sorry bro I'll clarify I took the stocker off yesterday and put the 1 1/2" longer motion pro on and I have raised bars. The only way I could get it idoling was taking the adjuster nut off both the carb and throttle to achieve any slack to let the slide down. I bought the ktm t3 and man what a slick cable, not only does it have threaded ends(no safety ties) but it fits better than the gasgas 1 1/2". The problem for me with the gasgas cable is that yes they make it 1 1/2" longer but theyake the housing for the cable longer too so there is not enough cable exposed. Buy the ktm t3 it really worked out well for me and is of much higher grade than the 1 1/2" longer cable! Part #10-3000
__________________
trevor |
#43
|
||||
|
||||
Quote:
|
#44
|
||||
|
||||
Jake how would water get in to the slide when it's a threaded end on top of the carb? I wouldn't even think the rubber boot is of that much importance.
__________________
trevor |
#45
|
||||
|
||||
I've got no idea trev. But how would water get in the top of the slide and no where else. Only happening after changing the cable. And never happening once adding some sealant and tie wire?
|
#46
|
||||
|
||||
Hmmm I'll have to watch when I wash my bike today then, cause I just put the t3 on, I'll take the slide out and see if I can force water through the threaded fitti to make sure mine isn't alowing water through. Super nice not to have to safety wire though with threaded fittings on both ends!
__________________
trevor |
#47
|
||||
|
||||
Quote:
__________________
Believe nothing, no matter where you read it or who has said it, not even if I have said it, unless it agrees with your own reason and your own common sense. [Buddha] |
#48
|
||||
|
||||
No pressure cleaners at this end. Will have to double check things myself too. Got me puzzled.
|
#49
|
||||
|
||||
There is no problem with the length of the GG specific cable. Look closely at the anchor on the carb side of the cable. Its a bit larger than the OEM cable, and if there is the slightest imperfection, it will not fit correctly and pull to the top of the needle retainer in the slide. This will make the cable appear short. Clean this up with a fine file if neccessary, but be careful not to nick the actual cable strands. Verify fit and all should be well.
|
#50
|
|||
|
|||
Quote:
__________________
Bryan 2013 Husaberg TE250 - Current 2011 GasGas EC300 - OLD STEED 2011 Husaberg FE390 - OLD STEED 2010 Yamaha WR250F - OLD STEED #53B I dream of a better tomorrow, where Chickens can cross the road, and not be questioned about their intentions. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
securing throttle cable | flybars | Enduro Intake/Carburetion - 2 stroke | 6 | 05-09-2010 04:29 PM |
Throttle Cable Mishaps | carlg | Enduro Intake/Carburetion - 2 stroke | 11 | 01-24-2010 09:22 AM |
Throttle Cable | steve | Enduro Intake/Carburetion - 2 stroke | 5 | 02-14-2009 02:39 PM |
throttle cable | steve | Enduro Intake/Carburetion - 2 stroke | 5 | 02-08-2009 06:17 AM |
Throttle cable | dave948 | Enduro Intake/Carburetion - 2 stroke | 7 | 10-10-2008 04:16 PM |