|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Jetting seem right?
After pulling my SC and putting the Keihin back on I decided I would check jetting on the carb. I never checked it since I bought the bike and it is running great as far as I am concerned. Does this combo seem right? I have checked the database and cannot really find anyone running the same. I ride between 600-2500? elevation.
2011 ec250 164 38 CGJ needle 2nd clip I had to get the old magnifying glass out to read the needle, but I?m pretty sure that?s what it said. Like I said, it runs good, minimal spooge if any. If anything it would be nice to have a little more snap on the bottom.
__________________
Brad 2011 Ec250 1982 Land Rover Santana Ligero Last edited by Wbdisco; 01-28-2024 at 06:10 PM. |
#2
|
|||
|
|||
Jetting Database Thread
Go to the jetting data base thread and start at page 11. Everyone has their jetting specs listed there. It has anything and everything right there. Its a wonderful resource.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#3
|
||||
|
||||
I?ve browsed through the database and the jetting 101. I couldn?t find anyone with the 164 main or a listing of the needle I have. I?m still learning the jetting stuff. It runs good so I don?t want to mess with a good thing, just curious on the numbers.
__________________
Brad 2011 Ec250 1982 Land Rover Santana Ligero |
#4
|
||||
|
||||
Just curious - where are your idle mixture screw and your idle screw adjustment set? How many turns out for each one?
jeff
__________________
|
#5
|
||||
|
||||
I will double check when I get home. If memory serves me though, I believe the AS is around 1.5. Idle is perfect at 1250rpms all day. I?ll chime back in later when I get off work.
__________________
Brad 2011 Ec250 1982 Land Rover Santana Ligero |
#6
|
||||
|
||||
AS 1-1/8
Idle 7 3/4
__________________
Brad 2011 Ec250 1982 Land Rover Santana Ligero |
#7
|
||||
|
||||
Plot thickens boys. Had some spare time to really take a look at this carb and settings. I?ll post this on the database thread as well just to document.
Keihin 36mm (36 cast on cap) 165 Main 38 Pilot CGJ needle 2nd position with shim( didn?t notice that the first time I pulled it) Slide stamped 65 AS 1-1/8 Idle 7-3/4
__________________
Brad 2011 Ec250 1982 Land Rover Santana Ligero |
#8
|
||||
|
||||
Anyone? Seem overly lean? I have no clue on how to interpret the needles.
__________________
Brad 2011 Ec250 1982 Land Rover Santana Ligero |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
A Few Jetting Basics (ie Jetting 101) | n_green | Enduro Intake/Carburetion - 2 stroke | 8 | 05-23-2014 05:42 PM |
Uk Jetting | Packman | Enduro Intake/Carburetion - 2 stroke | 1 | 07-26-2013 04:28 PM |
jetting?? | rbm33 | Enduro Engine - 2 stroke | 8 | 01-29-2013 07:12 AM |
Anyone using JD Jetting kit in UK ? | DaveH | Enduro Intake/Carburetion - 2 stroke | 13 | 11-04-2010 08:18 AM |
jetting | macho comacho | Enduro Intake/Carburetion - 2 stroke | 21 | 03-10-2009 03:11 AM |