|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
2012 plastic upgrade???
Hi all,
My 2012 has seen better days and needs a bit of loving. As it stands there are more cable ties than plastic Can I upgrade to say a 2015 plastics and if so what needs to be changed? I need a new rear fender support as mine got smashed on my back after a drop off in neutral. Would this need too be upgraded or do I just get the replacement and the new gear will fit? I have spoken with Jeff over here in Oz and he is pretty sure it will but has a bit of gear on back order and cannot match it all up right at the minute. Any info would be great. Need to get the old girl looking good again, she is getting jealous of the pretty Cr 5 next to her. Cheers Mark
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E |
#2
|
||||
|
||||
Everything should bolt right up. Do you have the alu. sub frame? If not the side # plates are a little different.
__________________
'12 XC 200 TTX Sold '15 XC 250E Sale pending |
#3
|
||||
|
||||
This is what I have heard though it is fairly costly just to check.
I do have the plastic subframe so the side panels will have to be the 12 model . Thanks for your help John. Mark
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E |
#4
|
||||
|
||||
I installed a 14 kit on mine no problems, except front fender has extra hole for fender brace under headlight and the side panel clip in tabs are a little different on the alum subframe. mc center has them listed to fit 13-15.
http://www.motocrosscenter.com/ecomm...ucts_id=132829
__________________
15 GASGAS EC 250 19 Sherco SE 125R |
#5
|
||||
|
||||
Ok, so everything fits except front fender. Mine has a plastic sub frame. You say they have different tabs for the aluminium one.? Will they work with my plastic sub frame though?
Cheers Mark
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E |
#6
|
||||
|
||||
The front fender fits fine, you could add the bracket or take the cheap route like me and fill the hole with white sealant you don't see it with the headlight.
The side panels can be made to fit the plastic subframe with some slight trimming on the back side. Then I drilled a small hole in the subframe and used a self tapping screw to secure the lower portion no big deal.
__________________
15 GASGAS EC 250 19 Sherco SE 125R |
#7
|
||||
|
||||
Oh ok sounds good.
Thanks for the info guys. Now do I go for the 15 look or the 16? Cheers Mark
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E |
#8
|
|||
|
|||
Here is my 13 with 15 plastics
__________________
Dick Carnes "If ya run, you'll only die tired" 2019 EC 300 2018 GP 300 2013 XC 300 (sold) 2006 DE 300 (buddy has it) |
#9
|
||||
|
||||
Nice, where did you get the plastics kit?
Did it come already stickered up? Cheers Mark
__________________
Xr 250 ( first bike) 98 Rmx 2007 Gas gas 300(swapped for trials bike) 2008 280 Raga replica 2012 Gas gas ec 300 E |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fork upgrade | rbm33 | Enduro Suspension | 7 | 11-11-2023 08:18 AM |
2012 Seat & plastic black Rear fender support | seitz331 | Parts | 3 | 11-29-2016 01:08 PM |
2012 plastic fix? | knave | General Discussions & Announcements | 0 | 07-25-2014 12:07 AM |
Ohlins TTX upgrade | Berkyboy | General Discussions & Announcements | 14 | 10-23-2011 07:59 AM |
Why Upgrade from a 2005 to a 2011? | celler | General Discussions & Announcements | 36 | 10-18-2010 05:45 PM |