|
"Wanted to Buy" & "Want To Trade" Bikes or Parts |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
WTB 1993 Honda XR 250 Frame
Looking for a sound frame. I think the 87 to 94 frames are the same. Cosmetics not important, going to powder coat it anyway. The peg mount on mine are a little bent and beat up.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#2
|
|||
|
|||
Bump, any 84 to 95 XR250R frame would be acceptable.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#3
|
||||
|
||||
Do like I did.
Get some foot peg mounts from an aluminum framed bike and weld those to the XR's frame. |
#4
|
|||
|
|||
Would you have any photos?
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#5
|
||||
|
||||
I this on my Gas Gas. Sadly, photos disappeared.
http://www.gasgasrider.org/forum/sho...ght=FOOT+MOUNT |
#6
|
|||
|
|||
No worries, nice thread, I may go with that type of repair. I just got it and I will start a build thread on it next week.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#7
|
|||
|
|||
SUCCESS! Found a pristine 94 Frame, it was just delivered yesterday.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#8
|
||||
|
||||
That is a good one to get. And earlier years (pre 1990) don't have tabs on frame for mounting rear master cylinder for rear disk brake.
The frame and swingarm are beefed up a tad starting in 91 over the previous years of that generation of XR. Brakes are a touch better too. The brake master cylinder on the front doesn't provide as much leverage as a CR master. I always put a CR front master cylinder on when I was racing them in the early and mid 90s... And after trying many different brake pads - I always ended up back with the stock nissin pads. Best feel, performance & wear. You can substitute XR650L brake pads in the front. They have more material to the inboard on the rotor - larger pad for better stopping. In '96 redesign they started using complete CR spec brakes front and rear.... jeff
__________________
|
#9
|
|||
|
|||
Thanks for the info! I actually have a CR front master cylinder sitting on the shelf.
I just did a test fit on the triples and forks to the new 94 frame. The steering stops are dead on match to the XR forks.The RM forks and the XR fork tubes are 36 inches from the bottom of the axle to the top of tube.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar Last edited by Moto7man; 05-28-2022 at 10:07 PM. Reason: Photo problem |
#10
|
|||
|
|||
Here is one more photo, stock rm caliper with bracket which bolts right up.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1993 gas gas trials 250 | r1chard06 | Trials Engine | 1 | 01-10-2019 10:15 AM |
Gas gas trials 1993 upside down forks | r1chard06 | Trials Suspension | 0 | 01-09-2019 02:11 PM |
umm video of my racing the 1993 RM 250 *DANGER | wheelie | Pictures & Videos | 2 | 09-20-2012 08:49 PM |
Link to WEC Heinola Finland Frame by Frame | REVERUP | Pictures & Videos | 0 | 09-16-2012 09:31 PM |
1993 contact 327 cc oils required? any advice please | darren1 | Enduro Engine - 2 stroke | 2 | 03-31-2011 01:41 PM |