Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 07-19-2010, 12:33 AM
chucky chucky is offline
Member
 
Join Date: May 2010
Posts: 41
Default Help - 2007 EC 200 jetting

I have read evrything regarding jetting on this forum , the problem is I live in South Africa and have limited access to the different needles described in this forum . The local Gas Gas agents recomend and use a needle that canbe purchased from KTM agents - N3EH , however I dont think this needle works well in the 200 , but I might be wrong that is why I am posting to get advice !!
I have also tried a N3CG needle which is a little better but still not perfect , I know that it is richer on the straight portion and half a clip richer on the taper . I think these needles are too lean on the 1/4 to 3/4 throttle range , also when I do a plug check it is black and wet ( this confuses me even further .

Altitude : 1600 m above sea level ( 4000- 5000 ft)
temp : 40 -60 deg fahrenheit ( winter ) 70-90 deg fahrenheit ( summer )
currently in winter

The humidity is low and quite dry especially in winter

I use 95 pump gas unleaded and premix ratio of 40:1 full synthetic oil ( GRO)

My setting with the N3EH needle was as follows :

N3EH # 4 ( at #3 and #2 there is a bog or slight hesitation when giving throttle from low RPM's in the midrange , WOT there is no problem )
Main jet 170
Pilot jet 42 ( cant quite get the airscrew correct and idling was not great - settled on 2-21/2 turns out
# 6 slide
float level is correct
plug was black and wet with these settings , My feeling was that mid was lean and top rich


N3CG 34 ( also hesitation in the mid when cranking the throttle from low rpm's with #3 and # 2 clip positions )
main jet 168
Pilot jet 40 , airscrew 13/4 out , idles better now but not perfect

This setting is better but I still believe it is not the best , Please advise me ,I am limited with needles here , I can get the JD jet kit but will take a couple of weeks , would this work?
Reply With Quote
 



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
what about this jetting? Gasgasogeros Enduro Intake/Carburetion - 2 stroke 3 12-11-2009 08:28 AM
Need help jetting an 06 EC 250 piperpilot12w Enduro Intake/Carburetion - 2 stroke 3 11-16-2008 11:19 PM
Harvest Classic 2007 European & Vintage Motorcycle Rally October 19 & 20, 2007 sanderjavant Republic of Texas 1 09-26-2007 05:18 PM
jetting help for 05 300 please... mackmack Enduro Intake/Carburetion - 2 stroke 5 09-03-2007 05:10 PM
06 300 jetting fury1 Enduro Intake/Carburetion - 2 stroke 1 07-31-2007 06:37 AM




All times are GMT -5. The time now is 07:52 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org