Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 10-07-2020, 09:12 PM
Lozarus Lozarus is offline
Member
 
Join Date: Oct 2020
Posts: 2
Default New to gas gas. Ec300 doesn?t scream

Hiya new to gas gas. Only had 250f?s in the past and 125
2 strokes..
Got a 2010 Ec300. Just had a new top end. Load of compression and runs well.
Has loads of bottom end but just seems to lack top end like it doesn?t scream. Is this just a characteristic of this engine? I think it?s running pretty rich so am gonna do the jetting. Any particulatar brand to go for or are jets jets?I?ve checked the power valve all ok. Repacked exhaust etc
It feels like apart from the bottom end kick in the first few gears that it runs out of puff feels like a cr125 top end. Any pointers would be appreciated.
My understanding is That I can lift adjust the height of the main jet to lean it out some? At the moment if i lean the bike Right over fuel doesn?t come out of the overflow
Thanks for your help


Reply With Quote


  #2  
Old 10-08-2020, 12:17 AM
(F5)'s Avatar
(F5) (F5) is online now
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Wellington New Zealand
Posts: 2,063
Default

RM250 needle NEDJ

St N1FE is best cut in two so you aren't tempted to keep it.
.

Then find the right main circa 175
__________________
'07 EC300 GG
'14 TXT250 GG
'? 496 CPI Cheetah RZ/RGV hybrid
'22 765 Street Triple RS
'21 XTrainer
'69 Stinger T125 Suzuki
'23 TRS 250RR (it's a Trials thing)
Reply With Quote
  #3  
Old 10-08-2020, 06:43 AM
Lozarus Lozarus is offline
Member
 
Join Date: Oct 2020
Posts: 2
Default

Thanks dude il give it a try !
Reply With Quote
  #4  
Old 10-08-2020, 09:50 PM
(F5)'s Avatar
(F5) (F5) is online now
Gold Level Site Supporter
 
Join Date: Jul 2006
Location: Wellington New Zealand
Posts: 2,063
Default

My mate has a 10. We put that needle in. He scoffed as they look the same. Now he won't shut up about it. Try clip 2 from top but don't be afraid to experiment. Our gas / altitude will likely be slightly different.
__________________
'07 EC300 GG
'14 TXT250 GG
'? 496 CPI Cheetah RZ/RGV hybrid
'22 765 Street Triple RS
'21 XTrainer
'69 Stinger T125 Suzuki
'23 TRS 250RR (it's a Trials thing)
Reply With Quote
  #5  
Old 10-09-2020, 09:01 PM
Gasser Nate's Avatar
Gasser Nate Gasser Nate is offline
Senior Member
 
Join Date: May 2010
Posts: 644
Default

If you really want a screamer throw a N3CJ in there, has a more angry transition than the NEDW. I run the NEDW though as the N3CJ can get tiring.
__________________
Back on a gassy! 2018 EC300! 🤘
Txt 280 07 to make me feel like a gumby again
Reply With Quote
  #6  
Old 10-11-2020, 05:05 PM
swazi_matt swazi_matt is offline
Senior Member
 
Join Date: May 2010
Location: From Swaziland, Now Hamilton New Zealand the “look but don’t touch” enduro heaven
Posts: 2,334
Default

Quote:
Originally Posted by Gasser Nate View Post
If you really want a screamer throw a N3CJ in there, has a more angry transition than the NEDW. I run the NEDW though as the N3CJ can get tiring.
agree, if you are looking for a more old-school 2t hit, then go for the N3** needle, the NE** will still scream, but it is much smoother getting there
__________________
2003 txt250 Pro
2013 Ossa 280i
Reply With Quote
  #7  
Old 10-13-2020, 01:17 AM
Sdogg Sdogg is offline
Member
 
Join Date: Aug 2020
Location: New Zealand
Posts: 6
Default

Make sure choke circuit is closing completely, had the same issues and that?s what it ended up being.
Reply With Quote
  #8  
Old 10-13-2020, 09:32 PM
Moto7man Moto7man is offline
Member
 
Join Date: Aug 2011
Location: Murfreesboro,Tennessee
Posts: 2,537
Default My Specs

My specs below, see the jetting thread, 12 years of jetting info on that thread.
http://www.gasgasrider.org/forum/showthread.php?t=2162
Bike year & model = 2011 EC 300
Temperature = 90F+
Elevation (feet) = 0-100 ft
Main jet = 178
Pilot jet =40
Needle & notch = N3EG #3
Air screw setting = 1.5 out
Throttle valve/slide = stock

Stock head. V Force,Pwk II 38mm, Motul 710 40/1. Note: dealer had installed the ultra lean CHN needle which someone else posted was the needle used for emissions testing in Europe. Much more torquey off the bottom with just a little more hit in the mid and same top end rev out. On plug chop, good tan color.
Riding condition(engine load) deep sand.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300

"If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut."
―Comedian Lewis Black

"I think best when I have a wrench in my hands." Soichiro Honda

"Dreams are messages from the deep."
-Unknown Sardaukar
Reply With Quote
  #9  
Old 10-14-2020, 02:41 PM
swazi_matt swazi_matt is offline
Senior Member
 
Join Date: May 2010
Location: From Swaziland, Now Hamilton New Zealand the “look but don’t touch” enduro heaven
Posts: 2,334
Default

Quote:
Originally Posted by Sdogg View Post
Make sure choke circuit is closing completely, had the same issues and that?s what it ended up being.
good point, but i would think 10 years on, most of the cable chokes would have already presented these problems and have been replaced with the little on-carb button
__________________
2003 txt250 Pro
2013 Ossa 280i
Reply With Quote
  #10  
Old 10-14-2020, 03:41 PM
Jacob 'Berg Jacob 'Berg is offline
Senior Member
 
Join Date: Mar 2014
Location: Scottsdale, AZ
Posts: 589
Default

If jetting alone does not achieve the top end range you are looking for you may consider some other options, such as 1) FMF fatty or PC expansion chamber 2)less pre-load on the power valve 3) exhaust port height/base gasket thickness

All of these options will have an affect on where the bike is making power, but with the 300 you may find that giving up a little on the bottom end of the power curve for faster revving/more over rev is worth it.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
UNI filter doesn't fit, WTF?! Why Z? Enduro Engine 4 stroke (including EFI & Exhaust) 7 05-29-2014 05:23 PM
My powervalve cam t thing doesn't look right rgranger Enduro Engine - 2 stroke 12 07-11-2011 12:41 PM
Why doesn't this work? Caravan Monster Enduro Electrical & Wiring 6 12-11-2010 12:48 PM
It doesn't fit.... stay_upright General Discussions & Announcements 7 03-04-2008 12:55 PM




All times are GMT -5. The time now is 02:15 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org