|
Enduro Suspension Tuning & maintenance of Enduro forks, shocks, etc |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
WTF is wrong with my shock?
http://i1258.photobucket.com/albums/...psb30c3a41.mp4
Re-greased the swingarm and linkage bearings 40k's (1 ride) ago. When I put it back together everything was super smooth, no binding at all. Torqued everything up as per the torque table on this site (which is the same values as the '11 GG user manual). I'm 90% sure everything was normal on the ride I just went on, although I did notice the rear felt harsher and kicked more over square edges and decent sized logs. Bought it home, washed it, put it on the stand to play with forks. Took it off the stand, it's making horrible noises as per above video. Sag figures are normal, although if I let the bike sag under its own weight without pumping it up and down it only sags 5-10mm. So something isn't right. Any opinions?
__________________
Current: 2014 Gas Gas EC300R _____________________________________________ Previous: 2011 Gas Gas EC300 ELC 2004 KTM 300 EXC |
#2
|
|||
|
|||
Anyone got bearing part numbers? May as well order them from the bearing shop tomorrow.
__________________
Current: 2014 Gas Gas EC300R _____________________________________________ Previous: 2011 Gas Gas EC300 ELC 2004 KTM 300 EXC |
#3
|
|||
|
|||
'11 EC 300. Sachs rear end if it matters.
__________________
Current: 2014 Gas Gas EC300R _____________________________________________ Previous: 2011 Gas Gas EC300 ELC 2004 KTM 300 EXC |
#4
|
||||
|
||||
Nice boots! and your dog bones are upside down!
Start at the beginning. It looked like it was doing some funky binding up at the top of the stroke. I couldn't tell where the squeak was coming from from the video but I'd start by disconnecting the front pivot/dog bone. The other should easily rotate all the way back smoothly. Then disconnect the lower shock mount and check the range of motion of the rest of the linkage. Pull the shock and remove the spring. Run it through its stroke and make sure its compressing and rebounding correctly (the full length of the stroke). Also listen for any sounds. If I remember correctly the Sachs shock has a check valve that can get quite noisey. Maybe bit of research there will turn up more answers. |
#5
|
|||
|
|||
Quote:
We have the full bushing oring kit for you if you need. Contact me. Rob
__________________
www.synergyseals.com 209-938-9726 Being BOLD is BOLD! However, being confident is certain! Ride with confidence again! Made in the USA |
#6
|
||||
|
||||
Do you have anything for the Ohlins 888 Rob?
__________________
2013 GasGas 300 2004 GasGas 200 2011 GasGas 300 Ortonville Minnesota |
#7
|
||||
|
||||
Nathan if you end up getting bushings through Synergy can you grab me a spare 2 x bushings to save on postage (the ones on the dog bones). Wouldn't mind having some spares.
PS. Had a chance to pull it apart yet? |
#8
|
|||
|
|||
Quote:
Flat out with work until the weekend so will have a look then hopefully can fixit quickly, have a ride to go to Sunday..
__________________
Current: 2014 Gas Gas EC300R _____________________________________________ Previous: 2011 Gas Gas EC300 ELC 2004 KTM 300 EXC |
#9
|
|||
|
|||
And the culprit was.........
When I re-greased them last time I put the swingarm bushings in the wrong way. They were in turn binding against the frame Quick fix in the end, nothing wrong with the bearings either. At least I now have a new set of bearings here and some bushings on the way for when they do actually go |
#10
|
|||
|
|||
Don't you hate when out do that? Doing the linkage and swingarm bushings /bearings today. Will definitely watch as I put it back together.
As a side note, pivot works linkage kit uses o-rings instead of the seals, much nicer. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Is this power valve lever plate wrong? | mark250ec | Enduro Engine - 2 stroke | 2 | 09-06-2011 05:39 PM |
What is wrong with my Clutch/Drivetrain? | SideshowBob | Enduro Engine - 2 stroke | 17 | 05-09-2011 10:56 AM |
Time is wrong | Brian | Suggestion Box | 3 | 12-10-2009 03:33 PM |
wrong fmf 200 de pipe? | whodat | Enduro Engine - 2 stroke | 9 | 12-26-2008 06:19 PM |
is it wrong to- | mountain thumper | General Discussions & Announcements | 5 | 06-07-2008 10:10 PM |