Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Chassis & Body

Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing.


Reply
 
Thread Tools Display Modes
  #1  
Old 03-20-2017, 07:26 AM
Blaze00 Blaze00 is offline
Member
 
Join Date: Mar 2017
Location: Written wv
Posts: 5
Default 17 ec300 crossover info?

Hi, new to the forum. I just got a new ec300. Been on Yamaha for the past decade or so. I've never had a bike that was hard to get parts for. So far I love the bike, but can't find parts.

My question is....

Are there parts I can get from older models or other bikes.

Interested in rad guards, radiators, plastics, brake pads, you know stuff that im gonna break.

Thanks for any info


Reply With Quote


  #2  
Old 03-20-2017, 07:53 AM
Anders's Avatar
Anders Anders is offline
Gold Level Site Supporter
 
Join Date: Nov 2009
Location: Kongsberg, Norway
Posts: 1,113
Default

Welcome!

As you are in the US, I would take a look at this thread:
http://www.gasgasrider.org/forum/showthread.php?t=22505

I guess that should solve all your part woes in a click or two
__________________
Anders

"So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie)

2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper
2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper
1998 Bimota Supermono
1986 Duc Mille S2
1975 Guzzi sidecar hack
1961 Morini Corsaro 125
etc
Reply With Quote
  #3  
Old 03-20-2017, 05:32 PM
hamilton's Avatar
hamilton hamilton is offline
Gold Level Site Supporter
 
Join Date: Nov 2012
Location: Elkton Md
Posts: 452
Default

Congrats on the new ride!

Parts aren't hard to get if you look in the right place.
Matto's cycle has about anything you might need in stock, give them a call.
__________________
15 GASGAS EC 250
19 Sherco SE 125R
Reply With Quote
  #4  
Old 03-22-2017, 05:09 PM
Blaze00 Blaze00 is offline
Member
 
Join Date: Mar 2017
Location: Written wv
Posts: 5
Default

So, pretty much no aftermarket products then?
Reply With Quote
  #5  
Old 03-22-2017, 05:29 PM
2012bluestreak's Avatar
2012bluestreak 2012bluestreak is offline
Member
 
Join Date: Mar 2016
Location: Toronto, Ontario
Posts: 7
Default

If you do some referencing on the gas gas web site the exploded view manuals have part numbers, so for example 2017 front brake pads are same part number as many other years ( I checked 2011) We know EBC and others make brake pads that fit . So with some research I think you will find some aftermarket parts. Check Rocky Mountain or Dennis Kirk they have some years of gas gas listed
__________________
2010 EC 300

Reply With Quote
  #6  
Old 03-22-2017, 06:39 PM
pscook's Avatar
pscook pscook is offline
Platinum Level Site Supporter
 
Join Date: Oct 2011
Location: Shoreline, WA
Posts: 1,164
Default

I believe that Gassers are built using aftermarket parts. Most everything is off the shelf parts, except the engine cases, frame, and swingarm. All bearings are easy to source, brake pads cross to other common sizes, YZ footpegs. I believe Polisport makes plastics, but I don't know who in the US is a dealer.

Regarding radiator guards, you will have to get bike specific, but I don't believe that GasGas sells those so you are looking aftermarket anyway. I know that lots of folks swear by the Chinese ebay radiators, and some KTM rads might fit (narrow selection of years and model, I believe). Sunstar makes sprockets (no common crossover on those), as stated EBC makes rotors, Nissin makes the brakes so you can use CR front brake levers and pads.

LOTS of aftermarket options if you look around a bit, but yes, somethings are just different enough to be a little bit of a challenge.
__________________
Phil
(New bike pending...)
Reply With Quote
  #7  
Old 03-23-2017, 09:14 PM
memphis2857 memphis2857 is offline
Senior Member
 
Join Date: Aug 2011
Posts: 970
Default

Enduro engineering makes radiator braces and Unabiker makes a full radiator guard. The rear sprocket is the same as the red Huskys. Brakes can be sourced from late model cr250's or you can call Budd Matto or Halls Cycles and have them in a day or so. Air Filters can be had from Twin Air or you can buy late model CR 250 air filters and make them work. I run DT-1 air filters from the older GasGas bikes and they work just fine also. Your dealer can get your plastics for you.

You do have to get a little creative if your looking for anything other than OEM but there is stuff out there. On the plus side these bikes are built like a tank and are great in stock trim so you really don't need much.


Sent from my iPhone using Tapatalk
Reply With Quote
  #8  
Old 03-23-2017, 09:15 PM
memphis2857 memphis2857 is offline
Senior Member
 
Join Date: Aug 2011
Posts: 970
Default

One other thing. The stock AJP clutch master cylinder has given a few of us problems. You can buy a rebuild kit from Matto or you can replace the whole thing with a 9.5mm 167 Magura unit. This will also allow you to buy aftermarket levers.


Sent from my iPhone using Tapatalk
Reply With Quote
  #9  
Old 03-24-2017, 04:09 AM
poelinca's Avatar
poelinca poelinca is offline
Senior Member
 
Join Date: Jul 2015
Location: Bucharest, RO
Posts: 302
Default

Quote:
Originally Posted by memphis2857 View Post
One other thing. The stock AJP clutch master cylinder has given a few of us problems. You can buy a rebuild kit from Matto or you can replace the whole thing with a 9.5mm 167 Magura unit. This will also allow you to buy aftermarket levers.


Sent from my iPhone using Tapatalk
Regarding the levers, I'm using these for nissin brake and ajp clutch (very good quality for the money)
http://www.motocrosscenter.com/shop/...ue-151756.html
__________________
'14 EC300
Reply With Quote
  #10  
Old 03-24-2017, 06:56 PM
Blaze00 Blaze00 is offline
Member
 
Join Date: Mar 2017
Location: Written wv
Posts: 5
Default

Thank you fellas, very helpful
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Ec300 2012 rear brake pedal bearings etc info MYBOARDSNOTFLAT Enduro Chassis & Body 2 05-12-2015 04:47 AM
Help! 2003 EC 300 Nissin Rear Master Cylinder Crossover Part(s) Info... tprnottp General Discussions & Announcements 2 02-26-2014 11:42 PM
Ec300 hub crossover? EcEvan03 Enduro Chassis & Body 1 06-11-2012 02:20 AM
So, I keep seeing conflicting info: 45 or 48 forks for EC300? rgranger General Discussions & Announcements 20 10-21-2010 07:37 PM
Need info on 2008 EC300 Scott's Submount BCTrialsguy General Discussions & Announcements 6 05-20-2010 07:37 AM




All times are GMT -5. The time now is 09:11 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org