|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Torque Specs EC 125 2005
Im back like always. Today im asking for torque specs.
1. What are the torque spec of the bolts holding the front axle? That are clamping the axle to the fork. 2. What are the torque specs for A, B and C. There are gonna be nuts there. wewew.jpg Last edited by Noobi06; 12-07-2022 at 02:26 PM. |
#2
|
|||
|
|||
And what is the torque specs for the rod. One nut go into the swingarm and one go into the rocker arm.
|
#3
|
||||
|
||||
|
#4
|
||||
|
||||
From the 2015 user's manual:
Linkage bolt M14x110 100NM (that would be your A B and C) Swingarm bolt M14 80NM General: M4 nuts and bolts 3NM M5 nuts and bolts 6NM M6 nuts and bolts 10NM M8 nuts and bolts 25NM M10 nuts and bolts 45NM The complete list for the chassis: Steering nut M24 40NM Rear shock bolt M10x50 45NM Swingarm bolt M14 80NM Brake disc bolt M6x14 12Nm Front axle bolt M20 50NM Brake caliper bolt M8x30 30NM Engine mount bolt M10x118 40NM Rear sprocket bolt M8x30 30NM Subframe bolt M8x50 25NM Brake banjo bolt - 6NM Upper clamp bolt M7x30 15NM Lower clamp bolt M7x30 11NM Spokes - 1,5NM Rear axle nut M20 100NM Linkage bolt M14x110 100NM Rear brake pedal bolt M8x45 25NM
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#5
|
|||
|
|||
Oh so the linkage bolt is all 3 holes?
According to my manual, there is a linkage screw that should be at 81 nm. There is a rocker screw also at 81 nm. Then theres a suspension flange screw at 29nm. Lastly theres also a rear shock bolt at 39nm. Can you link A, B and C to those screws? I dont know what is what. I do not know the names. Please state what A, B and C is and the names and the torque values according to what i said ^up^ etc. Also, side question, what is the Transmission rear plate nut. its supposed to be torqued at 29 nm. thanks in advance Anders. ur always my help )))))))) |
#6
|
||||
|
||||
I sent you a PM
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#7
|
|||
|
|||
So since my linkage bolt should be at 81 nm, all those 3 bolts should be at 81nm
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Torque specs :( | NM_GG_Rider | Enduro Chassis & Body | 9 | 07-01-2021 05:35 AM |
Need torque specs for 2018 XC 300 please | GG221 | Enduro Chassis & Body | 5 | 05-05-2019 05:05 PM |
Late 90s torque specs | Rpronick | Enduro Engine - 2 stroke | 3 | 07-19-2016 04:27 AM |
torque specs | kstreet | Enduro Engine - 2 stroke | 1 | 01-28-2011 07:05 PM |
Torque Specs | steve | Enduro Engine - 2 stroke | 8 | 02-26-2008 09:30 PM |