|
Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc. |
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
FAN KIT FOR EC300 question
Hi all
Wanting to install fan on my gg. But it's not original kit. So i wondering what "voltage rectificator from AC to DC" is for, and can i install fan without it? |
#2
|
||||
|
||||
The fan is then most likely a DC fan. What model of bike do you have? Only the last models have DC system. If you have any older bike you must install the rectifier since it has an AC system..
Sent fra min E5603 via Tapatalk
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#3
|
|||
|
|||
the fan is the one that comes on the GG trials bikes.
https://www.greenlandmx.com/en/p/oem...ifier-txt/7008 I have one on mine, but since it does not have the battery i have the rectifier. I will find out what information is posted on the unit later today.
__________________
2003 txt250 Pro 2013 Ossa 280i |
#4
|
|||
|
|||
|
#5
|
|||
|
|||
with or without e-start is the actual question i think.
sorry nothing marked on my rectifier, may have worn off
__________________
2003 txt250 Pro 2013 Ossa 280i |
#6
|
|||
|
|||
__________________
2003 txt250 Pro 2013 Ossa 280i |
#7
|
|||
|
|||
That rectifier should be an easy install. The black and red are your DC output to the fan. The yellow and white wires are for AC. You need to locate the yellow wire that comes out of your stator and connect into that circuit with the yellow wire on your rectifier. The white wire on the rectifier is then grounded to complete the circuit. The fan will run whenever the engine runs.
In the kit there is a thermoswitch you can add to the circuit. Put it in series with the white wire. This will let the thermoswitch ground the rectifier to create your DC for the fan. This is the way the kit is intended to be used so the fan engages only when the coolant reaches the temperature limit. On the AC input it does not matter if you hook up the wires opposite (connect the white and ground the yellow).
__________________
2011 EC250E |
#8
|
|||
|
|||
Thanks all, but i don't understand - should i install rectifier with fan, or i can install it without rectifier?
|
#9
|
|||
|
|||
You should use the rectifier.
__________________
2011 EC250E |
#10
|
|||
|
|||
Add Fan Question
This is kind of a dumb question but I want to to mount a fan on my 84 RM 250. I am going to use a Spal Fan with a switch. This is the stator before restoration. My stator only has the two AC wires. Do I need a new stator with dedicated power source wires? Like in the video below,
URL="https://youtu.be/zEQu-JMfUSg"]https://youtu.be/zEQu-JMfUSg[/URL]
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar Last edited by Moto7man; 08-10-2019 at 11:25 AM. Reason: resize image |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
12 EC300 mapping question | knocklife | Enduro Electrical & Wiring | 1 | 09-24-2014 12:45 AM |
06 EC300 Question | ECTim | Enduro Electrical & Wiring | 5 | 08-27-2014 04:29 PM |
Starter question 2011 EC300 | iamovru | Enduro Electrical & Wiring | 3 | 02-17-2014 12:01 PM |
Gas Gas ec300 plastics question. | Tricky | Enduro Chassis & Body | 4 | 01-07-2014 10:55 AM |
EC300 Dim Electrics Question | rogerc | Enduro Electrical & Wiring | 2 | 03-02-2009 11:47 AM |