|
|
|||||||
| General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
 |
|
|
Thread Tools | Display Modes |
|
#1
12-19-2010, 09:13 AM
|
||||
|
||||
New Gasgas owner - Parts Question
Is there someplace I can go to get a full list of crossover parts for my 2007 300?
I am guessing that there is crossover for the following items, but its very hard to find someone local with the knowledge to help: - Clutch and brake levers. - Shifter lever. - Air filter. - Clutch plates. - Bar clamps. - Sprokets? Sorry if I am overlooking it on this site. Thank you, Matthew
__________________
Believe nothing, no matter where you read it or who has said it, not even if I have said it, unless it agrees with your own reason and your own common sense. [Buddha] 
|
|
#2
12-19-2010, 09:17 AM
|
||||
|
||||
|
- Clutch and brake levers. moose has them
- Shifter lever. no known QUALITY replacement - Air filter. cr250r - Clutch plates. cr250r - clutch mod needed. - Bar clamps. haven't checked. - Sprokets? modern husky 4 stroke for rear, none for front?
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com 
|
|
#4
12-19-2010, 02:12 PM
|
||||
|
||||
|
Quote:
I did see the parts crossover list that has been posted. I thought for sure that some other manufactures levers might fit as well (like Honda, KTM or Husky). But no luck, huh?
__________________
Believe nothing, no matter where you read it or who has said it, not even if I have said it, unless it agrees with your own reason and your own common sense. [Buddha]
|
|
#5
12-19-2010, 04:03 PM
|
||||
|
||||
|
the moose levers are like $15.00...
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com
|
|
#6
12-19-2010, 06:36 PM
|
||||
|
||||
|
Quote:
I guess that I will go on the Moose website and look for a part number.
__________________
Believe nothing, no matter where you read it or who has said it, not even if I have said it, unless it agrees with your own reason and your own common sense. [Buddha]
|
|
#7
12-19-2010, 07:19 PM
|
||||
|
||||
|
my local shop just scanned catalogs for a moment and found them...
moose #1CDGS17 clutch lever i can't find the brake lever - but most honda 2 strokes 'should' fit, i know i've switched it to one that has a bigger offset (closer to the bar)... i'm sure it was less than $20.. i'd remember if i had to pay dearly for it...
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com
|
|
#8
12-19-2010, 07:36 PM
|
||||
|
||||
|
Quote:
__________________
Believe nothing, no matter where you read it or who has said it, not even if I have said it, unless it agrees with your own reason and your own common sense. [Buddha]
|
|
#9
12-19-2010, 09:53 PM
|
||||
|
||||
|
'07+ filter is different than older bikes and CR250 filter WILL NOT fit. Hammerhead make a nice shift lever with different offset tips available. I would still rather have a steel one though for durability. BRP should have bar clamps.
|
|
#10
12-20-2010, 01:29 PM
|
||||
|
||||
|
Quote:
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| dissapointed new gasgas owner | lukemonroe | General Discussions & Announcements | 11 | 10-26-2009 06:09 PM |
| New GASGAS owner - some opinions/help. | chuz | General Discussions & Announcements | 5 | 09-09-2009 03:41 PM |
| Newbie GasGas Owner with some ??? | rpduc | General Discussions & Announcements | 14 | 03-02-2008 05:17 AM |
| New gasgas owner | gasgasme | General Discussions & Announcements | 8 | 04-18-2007 10:41 PM |
Linear Mode
