Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > Other Bikes... > All Other Bikes...

All Other Bikes... KTM, Husky, VOR, Husaberg & Hondayamazuki...


 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 01-22-2017, 11:55 AM
Moto7man Moto7man is offline
Member
 
Join Date: Aug 2011
Location: Murfreesboro,Tennessee
Posts: 2,537
Default 94 CR 250 Ground Up Restoration IMS Wide Ratio Transmission Issue

I have been working on this restoration for about 18 months gathering parts. I am in mid assembly and I ran into a problem with installing the IMS Wide Ratio Transmission. I have a thread on another forum and some of the GG members already know about it. I have 4 of the 5 IMS gears installed without any problems at all. (2 on the mainshaft and 3 on the countershaft). The problem is the last C3 gear on the countershaft fits perfectly but the I.D. of the gear (with the bushing) is too big for the shaft. Any suggestions would be greatly appreciated.


This is the countershaft,the bigger gear is the stock Honda gear and the other gear is the IMS gear. Note the stock Honda bushing(collar)inside the IMS gear. Between C3 and C5 it is a bushing that rides inside C3, there are also a single washer on each side of C3. There isn't a spacer. The I.D of replacement gear is 24.98. The bushing(collar) O.D is 21.99 and the Bushing(collar) I.D is 18.99.I have attached photos showing the replacement gear loosely positioned on C5 without any collar so you could see the gap between gear and countershaft. I also included photos of C3 and C5 which show witness marks that they were previously mounted together. C3 and C5 seem to fit together perfectly except for the bushing(collar).
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300

"If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut."
―Comedian Lewis Black

"I think best when I have a wrench in my hands." Soichiro Honda

"Dreams are messages from the deep."
-Unknown Sardaukar

Last edited by Moto7man; 07-19-2017 at 10:16 AM. Reason: Spelling
Reply With Quote
 



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
DC conversion - not floating ground johnm Enduro Electrical & Wiring 39 03-04-2020 11:11 AM
Gas Gas Contact Jt 25 95 Restoration And Help Eyetech General Discussions & Announcements 1 03-18-2016 03:33 PM
2001 XC200 Restoration Project Lincolnlock Enduro Engine - 2 stroke 19 04-22-2014 03:42 PM
Hanging Idle after wide open GasGas Enduro Intake/Carburetion - 2 stroke 10 09-06-2013 04:13 PM
My Stomping ground swazi_matt Ride Reports 10 03-02-2011 09:35 AM




All times are GMT -5. The time now is 06:20 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org