|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
ec300 clutch problem
hi ive got an ec300 03 model and it stalls when put into gear,ive blead the clutch (back blead with syringe) fresh dot 4 fluid still no change also checked lever free play,so today i pulled the plates out and they look good no warpage,basket looks good no grooves,anyone got any ideas on what to check next also running on rock oil gro
|
#2
|
|||
|
|||
Slave cylinder seals?? Still have some air bubbles?
There might be something down a ways in this thread for you... http://www.gasgasrider.org/forum/sho...ighlight=slave Or search "slave" for more threads.
__________________
Ross '05 MC 250 '91 Husky 610wxe '04 Duc M800 R.I.P '06 Duc S2r 1000 R.I.P '07 Duc S2r 1000 still rubber side down... ---------------------------------------------------------- May be so... May be not so... My Website |
#3
|
|||
|
|||
thanks,no air bubbles in the system ive checked and double checked,now the slave cylinder are the seals easy to change,can anyone give me some advice on doing it as ive never had one apart cheers adam
|
#4
|
|||
|
|||
ec300clutch
hi i think its time to overhaul both clutch master & slave cyl also check the push rod from slave cyl to clutch pressure plate for wear good luck
|
#5
|
|||
|
|||
yea think im going to have to drop it into the mechanic,i cant find anything online the manual i downloaded would make good toilet paper,thats about it,plus ive never opened up a master cylinder or slave cylinder before
|
#6
|
||||
|
||||
Did you just start having problems with it or has it been getting worse?
__________________
07 GG EC 300 05 KTM 250 exc 99 KTM 640 enduro |
#7
|
||||
|
||||
Have you checked if the problem is lack of movement of the push rod? Is it actually moving much when you operate the clutch. I.e. is it drag because something's wrong in the basket or are the hydraulics just not working. Also I saw a bent pushrod once so maybe check it's nice and straight.
Also I assume the plates are not new? If they are they can sometimes be a bit weird for a while until they bed in. |
#8
|
|||
|
|||
no not new plates,i never checked the pushrod to be honest with you,(ill do that today)and the problem has only just started,to the point i cant ride the bike at all
|
#9
|
||||
|
||||
If it just started with no change from yourself then you'll just have to work your way through the system trying to see which bit isn't working as it should. I think there's a fair chance it's not the gubbins in the clutch basket, plates etc or you'd see the wear marks or plates would be out of spec. Worth checking nothing's come loose or out of place so that the pushrod is actually pushing the clutch apart as it should. They don't move very much so just a little problem could cause it not to work.
|
#10
|
|||
|
|||
thanks ian yes the pushrod is pushing the basket out but only say half an inch or so.i got a mechanic just up the road from me who knows his stuff so its going up there in the morning ill post the outcome when i find it just for other users refrence
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Starter clutch / gear problem | iancp5 | Enduro Engine 4 stroke (including EFI & Exhaust) | 12 | 01-28-2011 02:45 PM |
450 Clutch problem | trxpeter | Enduro Engine 4 stroke (including EFI & Exhaust) | 4 | 09-03-2010 12:38 AM |
Clutch problem sticky? | dank | General Discussions & Announcements | 16 | 05-26-2010 01:20 PM |
also an ongoing clutch problem...... | dank | Enduro Engine - 2 stroke | 2 | 05-19-2010 01:24 PM |
450 Clutch problem | mike989 | Enduro Engine 4 stroke (including EFI & Exhaust) | 17 | 01-02-2008 08:54 AM |