GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 09-02-2018, 06:48 PM
AZRickD AZRickD is offline
Senior Member
 
Join Date: Feb 2007
Posts: 1,839
Default Stock Jetting in 2018 XC300

I'm going through my new-to-me Demo 2018 XC300 (with EC pipe). Carb was said to have stock-ish jetting.

It's about 100F to 110F right now (37.8C to 43.3C) here in Phoenix with the riding elevation about 2000 to 3000 feet (1000m). But most prefer to head up to the mountains from 5000' to 7000+ feet and the temps dropping to 85F (or 70F after a rain).

So, essentially, in the past (pre-Lectron) I have had my winter jeting (central Arizona foothills at 3000 feet and about 40-60F), and my summer jetting (Prescott and Flagstaff at 7000 and about 80F). In my 2011 EC250 (with head mod), that would be 172/42 in the winter (maybe a little fatter), and 162/38 for Flagstaff summers.

I had been riding the new-to-me 2018 EC300 around, taking it easy, as my shoulder heals. I found the bike to run very clean. Starts right up. Idles nicely. No smoke after warm up. No spooge (zero spooge, not even a dusting).

The plug has many hours on it and is black and dry. It is jetted almost the way I would want it: Soft. It's probably a little too soft right now. I'd jet it leaner. When I swapped the FMF Power Core for a Turbine Core, the top-end got a little burbly.

So today I started digging into the bike to decide if I wanted to go to the bother of measuring the squish for modding and/or get a Lectron or just do the jetting dance.

I rotated the carb around to verify the jetting. N1EF needle with clip in the 2nd position from top. Whenever I see the clip moved to drop the needle, I wonder what profile is being compensated for. Main Jet is a 175. Pilot Jet is 40. Air screw 1.5 turns out. The N1EF needle has a pronounced taper that would be useful for our very long, deep sand washes to keep things cool. Other than that, I'm looking for another needle.

Jakobi and other have mentioned using other needels such as the NEDW needle. Any particular advice for my situation?

Since I have been using a Lectron for the last few years, I have given away most of my brass, so I need to buy some. Any advice for that?

[Edit] The results of the squish band measurement are in. 1.78mm with carboned up piston. 1.85mm with carbon scritched away with a razor blade.

Thanks.
Attached Images
File Type: jpg 2018GGEC300NeedlePlub.jpg (112.5 KB, 14 views)
File Type: jpg 2018GGEC300HeadPiston.jpg (116.6 KB, 16 views)



Last edited by AZRickD; 09-02-2018 at 08:19 PM.
Reply With Quote


Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2018 GasGas XC300 Flywheel Weight chunkysoup Enduro Engine - 2 stroke 15 12-03-2018 03:27 PM
Can you guess the identity of this new owner of a 2018 XC300 ?? AZRickD General Discussions & Announcements 47 10-09-2018 10:34 PM
2018 XC300 headlight options chunkysoup Enduro Electrical & Wiring 5 06-17-2018 08:02 PM
Picked up a 2018 XC300! Adrian200xc General Discussions & Announcements 8 11-06-2017 10:09 PM




All times are GMT -5. The time now is 11:56 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org