Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #11  
Old 02-20-2018, 06:31 PM
Gasser Nate's Avatar
Gasser Nate Gasser Nate is offline
Senior Member
 
Join Date: May 2010
Posts: 644
Default

Yes, Keg 👆


__________________
Back on a gassy! 2018 EC300! 🤘
Txt 280 07 to make me feel like a gumby again
Reply With Quote


  #12  
Old 02-21-2018, 04:15 AM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,994
Default

Different needles, different delivery, however not a whole lot of fuelling variance across the brands when it comes to the 72x72 300cc donks. Pretty much all running Vforce reeds coupled with a Keihin 36/38mm carb, and a free flowing exhaust. Ports for smooth power and excess squish/lowish comp.

Just a matter of finding a taper that provides the delivery style you like and then matching the clip position, pilot (and needle diameter; and/or slide number), and mains to suit particular engine and conditions.
Reply With Quote
  #13  
Old 02-21-2018, 06:25 AM
memphis2857 memphis2857 is offline
Senior Member
 
Join Date: Aug 2011
Posts: 970
Default

You have to throw that garbage stock needle in the trash can. It is terrible. Goes from lean to rich and causes the bike to have weak bottom end and then explode into mid-range.

I like the NEDJ or N3CH needles


Sent from my iPhone using Tapatalk
Reply With Quote
  #14  
Old 04-03-2018, 03:54 PM
thumperrider1 thumperrider1 is offline
Senior Member
 
Join Date: Sep 2010
Location: VA
Posts: 499
Default

Quote:
Originally Posted by memphis2857 View Post
You have to throw that garbage stock needle in the trash can. It is terrible. Goes from lean to rich and causes the bike to have weak bottom end and then explode into mid-range.

I like the NEDJ or N3CH needles


Sent from my iPhone using Tapatalk
Got my needles in today. I have the NECJ needle, N3CH and N3CJ. What main and pilot have you tried in with the N3CH? I'm east coast, sea level to 1000ft.
__________________
2018 XC300
Reply With Quote
  #15  
Old 04-03-2018, 07:28 PM
memphis2857 memphis2857 is offline
Senior Member
 
Join Date: Aug 2011
Posts: 970
Default

Quote:
Originally Posted by thumperrider1 View Post
Got my needles in today. I have the NECJ needle, N3CH and N3CJ. What main and pilot have you tried in with the N3CH? I'm east coast, sea level to 1000ft.


With the N3xx needles you will have to run a pretty fat main jet. I run N3CH 3rd clip, 180 main 42p A.S. 1.5 and jetting is spot on


Sent from my iPhone using Tapatalk
Reply With Quote
  #16  
Old 04-04-2018, 03:18 PM
thumperrider1 thumperrider1 is offline
Senior Member
 
Join Date: Sep 2010
Location: VA
Posts: 499
Default

Thanks for sharing. I have KEGS setting in there right now and will ride with it Friday and then try the N3XX combo after a few laps. Thanks!
__________________
2018 XC300
Reply With Quote
  #17  
Old 04-09-2018, 09:27 AM
thumperrider1 thumperrider1 is offline
Senior Member
 
Join Date: Sep 2010
Location: VA
Posts: 499
Default

NECJ was just too lean for my bike. Going to try the N3CH setup and also an NEDH for comparison.
__________________
2018 XC300

Last edited by thumperrider1; 04-09-2018 at 10:24 AM.
Reply With Quote
  #18  
Old 04-13-2018, 06:49 AM
Keg Keg is offline
Senior Member
 
Join Date: Aug 2006
Posts: 304
Default

Quote:
Originally Posted by Keg View Post
NECJ #2
MJ 175
PJ 42
AS 1 1/4
1000ft alt
65 - 85 degrees f.
95-98 octane gas
Back to #3 for most riding.

NEDW #3 for the GP300 is pretty good too.
__________________
EC300 2019 (11 Gassers owned, many more to go)
Reply With Quote
  #19  
Old 04-13-2018, 09:49 AM
RS1 RS1 is offline
Member
 
Join Date: Jan 2018
Posts: 12
Default

Now my EC 300 2018 work perfect with NEDW at 3

MJ 172
PJ 42
AS 1 1/2
Alt sea level
5-15 degrees C.
95-98 octane gas

but remove this damn cable choke, it is the cause of the majority of the problems
Reply With Quote
  #20  
Old 04-16-2018, 02:19 PM
thumperrider1 thumperrider1 is offline
Senior Member
 
Join Date: Sep 2010
Location: VA
Posts: 499
Default

I was also told to ditch the choke. Plan to do that as well.
__________________
2018 XC300
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Revised Jetting Specs NEDW Jakobi Enduro Intake/Carburetion - 2 stroke 197 09-19-2014 08:17 AM
'06 EC300 stock handlebar specs? brider Enduro Chassis & Body 0 09-16-2013 03:08 PM
What is the stock 200 needle and jetting specs shaheeb Enduro Intake/Carburetion - 2 stroke 3 03-24-2012 10:56 PM
2010 EC300 Factory Jetting Specs - WTF? JP4 Enduro Intake/Carburetion - 2 stroke 197 07-04-2011 11:03 AM




All times are GMT -5. The time now is 09:56 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org