GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Chassis & Body

Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing.


Reply
 
Thread Tools Display Modes
  #1  
Old 11-11-2017, 02:41 AM
AAH AAH is online now
Member
 
Join Date: Mar 2017
Location: Northern NSW Australia
Posts: 5
Default Frame wanted

Hello everyone, this is my first post. I've been lurking around here for a few months now and found lots of great info. I purchased a 2005/6 ec300 earlier this year. Although I have never been without a bike since I was 12, this is
the first dirt bike I've owned or ridden in 35 years. The bike had been treated badly by the previous owner and it took a few months to get to the stage where I could get it registered. Done about 20 hours on it now.

Anyway to the point of the post. Last couple of rides I've felt there something not right with the handling so I put a string line on the wheels. Way out, and to get the alignment even close the measurement from swing arm pivot to rear axle was 5mm shorter on the right side. So I put a plum line on the wheels and found they are way out of plum.Looking further I found the frame broken on the right hand side a few inches above the swing arm pivot. I know it wasn?t broken when I replaced the swingarm bearings but it could have been cracked on the inside and I've not seen it. Also the top of the frame near the steering head on the left side looks like it?s taken a hit from the fork leg at some stage. From the rear it looks like the top part of the frame is pushed over to the right, the shock seems to lean to the right, you can see from the photo the frame is out of alignment at the break.

A friend is an expert welder so while I don?t think it will be a problem to repair the break, I have my doubts we will be able to get it true. So does anyone have a good frame they would be willing to part with?

Cheers Tony.
Attached Images
File Type: jpg IMG_0232.JPG (119.7 KB, 41 views)
File Type: jpg IMG_0236.JPG (118.0 KB, 38 views)


Reply With Quote


  #2  
Old 11-11-2017, 12:51 PM
Zman's Avatar
Zman Zman is offline
Platinum Level Site Supporter
 
Join Date: Apr 2010
Location: Burbs of Chicago
Posts: 1,112
Default

I believe PEB has a frame for sale.
Reply With Quote
  #3  
Old 11-14-2017, 03:30 PM
AAH AAH is online now
Member
 
Join Date: Mar 2017
Location: Northern NSW Australia
Posts: 5
Default

I saw that PEB had a couple of frames but I think the cost to freight 1 to Australia would be more than the bikes worth. I was hopping someone in oz might have one.
Can anybody tell me if a frame from a 2000 model would be the same?
Reply With Quote
  #4  
Old 11-14-2017, 04:48 PM
PEB PEB is online now
Senior Member
 
Join Date: Aug 2006
Posts: 1,107
Default

I do indeed have two of them, but it would be ridiculously expensive to ship them down under.
Reply With Quote
  #5  
Old 11-15-2017, 12:58 PM
swazi_matt swazi_matt is online now
Senior Member
 
Join Date: May 2010
Location: Swaziland - Gods gift to off-road riding!
Posts: 1,819
Default

Quote:
Originally Posted by PEB View Post
I do indeed have two of them, but it would be ridiculously expensive to ship them down under.
But you could buy a whole lot of kit, boots etc to fill the inside of the frame and use the frame as the frame for the packaging that way you won’t pay duty on the frame hmmmmm!?
__________________
2010 ec 300
Reply With Quote
  #6  
Old 11-18-2017, 06:29 PM
AAH AAH is online now
Member
 
Join Date: Mar 2017
Location: Northern NSW Australia
Posts: 5
Default

Good idea Matt but I just don't need anything else right now.
I've had the frame welded, the alignment still isn't great, but it will have to do until I can get another frame.
I may be able to get a 2000 model frame but I don't know if it would be suitable. Can anyone tell me if they are the same?
Reply With Quote
  #7  
Old 11-18-2017, 07:29 PM
gasgasman's Avatar
gasgasman gasgasman is online now
Super Moderator
 
Join Date: Jul 2006
Location: Pearland ,Texas
Posts: 3,817
Default

The frames were changed in '03, the motor mounts are different. Also, the front of the motor is tilted down.
__________________
2018 GasGas XC 250
2015 GasGas XC250R

USFS Motorized Trail Maintenance Volunteer
Reply With Quote
  #8  
Old 11-19-2017, 01:11 AM
PEB PEB is online now
Senior Member
 
Join Date: Aug 2006
Posts: 1,107
Default

I can look into shipping if you would like. I'd let the frame go for cheap, like $100 plus shipping? I just spent $180 to ship 4 rims to Texas from Seattle.
Reply With Quote
  #9  
Old Today, 04:21 AM
AAH AAH is online now
Member
 
Join Date: Mar 2017
Location: Northern NSW Australia
Posts: 5
Default

Thanks gasgasman. I'll give the 2000 frame a miss.
Thanks PEB, it would be interesting to find out, but only if you have some spare time. Might just ride it as is for a while and then look for a later model in better condition.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Frame wanted AAH "Wanted to Buy" & "Want To Trade" 0 11-11-2017 02:39 AM
EC 300 frame, '10 - '11 wanted 5valve "Wanted to Buy" & "Want To Trade" 1 08-06-2016 05:26 AM




All times are GMT -5. The time now is 04:14 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org