|
Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Ec 300 jetting uk settings
I?ve had a few gas gas 300?s and all run spot on from new so never looked at the carb settings.
I?ve just got myself a toy to green lane on. Ec300 2007-2008 mint but runs shite. Tick over is good. Bottom end pulls well, takes a couple gears to clear when riding at low speed. Somebody has been trying to get thing right the settings are. Main 168 Pilot 38 Slide 7 Needle N1EF top clip. (Lean) AIr screw fully in. Spoke with Kev at gas gas uk He said standerd should be M 178 P 40 S 7 P N1EF middle clip AS 1-1/2 out.. That?s just gonna make it run richer right. Any input would be great on this. I?m a tech rider like it crisp. It’s got an FMF front pipe. If that makes any difference.. Thanks Darren |
#2
|
|||
|
|||
Go here:
http://www.gasgasrider.org/forum/forumdisplay.php?f=15 Or zero in on this: http://www.gasgasrider.org/forum/showthread.php?t=2162 The N1EF needle is garbage. Put in something useful.
__________________
2011 EC250E |
#3
|
||||
|
||||
Look i think Neil is being a bit circumspect when he says the N1FE is rubbish.
I'm not genuinely sure what circumspect means. I'm assuming it means complete absolute shite. Cut it in half so you are not tempted to use it. A piece of fencing wire sanded down in the drill could be better. I've been riding my 07 EC300 in the sun today wheeling up hills. Awesomeness. Look I think maybe I have been subtle in my answer and possibly missed my point. The base of the shitty N1FE bah i can't even speak its name without falling into a rage. The night was black, was no use holding back 'Cause I just had to see, was someone watching me In the mist dark figures move and twist Was all this for real, or just some kind of hell?
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
#4
|
|||
|
|||
Yes, as the guys said. Best is to cut the N1EF in half so that you never can use it again.
|
#5
|
|||
|
|||
Well i wasn't that enraged as to start quoting devil lyrics, until i actually made the switch form this absolute disastrous pile of smelly poisonous crap that is the N1EF needle, forgive me from typing it's name. The hours i spent trying to figure it out and the doubt that maybe the bike has a problem, a 2001' 300.
Anyway, stepping away from the darkness, read some threads here and bought a NEDJ. i was at N1EF@1 38 172 AS 100 turns out and it was shitty down low, also crap in the middle but ok high. (talking about throttle openings) now its the same only NEDJ@3 and AS 2-3 out and its very close to 100%. i mean the sputter is absolutely minimum at small openings and tunable with AS, anything after barely cracked open and it accelerates smoothly, even at extremely low rpm near the die out point below idle. Pretty tempted to melt the old needle into nothing. |
#6
|
||||
|
||||
666 the number of the beast
Hell and fire was spawned to be released Torches blazed and sacred chants were praised As they start to cry hands held to the sky In the night the fires are burning bright The ritual has begun, Satan's work is done N1FE And santa claus
__________________
'07 EC300 GG '14 TXT250 GG '? 496 CPI Cheetah RZ/RGV hybrid '22 765 Street Triple RS '21 XTrainer '69 Stinger T125 Suzuki '23 TRS 250RR (it's a Trials thing) |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Jetting Database - PLEASE ADD YOUR SETTINGS | MattR | Enduro Intake/Carburetion - 2 stroke | 347 | 03-30-2024 09:53 AM |
Apt smart carb settings database, please post your settings | IDAHOSPUD | Enduro Intake/Carburetion - 2 stroke | 8 | 12-13-2013 04:45 AM |
Help... 2012 EC 300 jetting settings... | richardexclaim | Enduro Intake/Carburetion - 2 stroke | 19 | 10-29-2012 07:17 AM |
sag settings.... | BryanMcc | Enduro Suspension | 12 | 09-04-2012 09:04 AM |
JD Jetting settings for linear power delivery? | SpeedyManiac | Enduro Intake/Carburetion - 2 stroke | 5 | 04-06-2010 06:17 PM |