|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Older GasGas Questions
I just bought a what the guy says is a 2000 250. After doing some research online it seems that a 250 in that yr should be red not blue. The stickers have all peeled on the plastic so I'm not sure what it is now. It has a number plate installed so no headlight. I have tried searching the VIN with no results. Was wondering if there was some common things i could check just to make sure of what i have before I start ordering a few small parts?
VIN:UTREC259806985069 |
#2
|
||||
|
||||
The first two digits, "25" indicates it's a 250. Someone probably liked blue and swapped the plastic along the way.
Jeff
__________________
|
#3
|
||||
|
||||
if i remember correct... the 2000 250 i had also had a 0 in the tenth digit.. a 2000 should not have a separate air box door to get to the air filter, you have to take the seat off...
gofasters.com has helped me with vin id before, but call them, the online catalog on the older ones is tough..
__________________
broken down over 60 slow rider.. |
#4
|
|||
|
|||
Also look by the shifter on the motor it will say EC25 and some #'s below that.
Just for reference, I have an 06 300 with the red(250) plastic instead of the blue. |
#5
|
|||
|
|||
Also look by the shifter on the motor it will say EC25 and some #'s below that.
Just for reference, I have an 06 300 with the red(250) plastic instead of the blue. Prior to this bike, I had a 300 motor in a 250 frame. That is why I would be more concerned with the motor than the frame. |
#6
|
|||
|
|||
You are correct. It has EC-25 a space and then 98. Followed by a series of numbers below that. I am assuming the 98 is the yr?
|
#7
|
||||
|
||||
what forks? rightside ups would be 99 and before.
what brakes? brembo is 99 and before. although the front end could have been switched out - this is the quickest way to tell without vin lookup...
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#8
|
|||
|
|||
Brembo Brakes. Would the 2000 model brake pads fit? I am assuming not because of having nissin calipers. Thank you all very much for the help
|
#9
|
||||
|
||||
brembo and nissin do not interchange.
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#10
|
||||
|
||||
If you are in California you could get a green sticker.
Good Luck
__________________
Rick 99 EC 200 06 RM 250 AMA D36 375X OTHG 375S ***Thanks for the support : Twin Air /O'Neil Racing / Race 100% / Matrix Concepts / ODI / Mika Metals |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
4 Stroke GasGas questions | Trailrider | General Discussions & Announcements | 11 | 08-20-2009 10:42 AM |
older ec , cdi location | widebear | Enduro Chassis & Body | 2 | 03-19-2009 10:38 AM |
Older Silencer fit 07-08 ? | cody1331 | Enduro Engine - 2 stroke | 1 | 07-21-2008 09:22 PM |
-07 -08 plastics on older ec 300 | matsa16 | Enduro Chassis & Body | 3 | 07-17-2008 09:10 AM |
Considering older model Gas Gas | EricP | General Discussions & Announcements | 2 | 06-03-2008 11:34 AM |