Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Intake/Carburetion - 2 stroke

Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 02-19-2009, 05:44 AM
jasont1532 jasont1532 is offline
Member
 
Join Date: Jan 2009
Location: stockholm,nj
Posts: 38
Default intermittant stuck throttle

i recently bought an 05 de300. it was brand new at dealer. from the very first ride i noticed sometimes (its getting more often) after a steady throttle(1/8-1/4) when i let off the gas the engine stays at that rpm until i crack the throttle again. cable adjustment is good. any ideas?


__________________
05 ec300
01 wr426
98 polaris trail boss
Reply With Quote


  #2  
Old 02-19-2009, 06:46 AM
eff's Avatar
eff eff is offline
Silver Level Site Supporter
 
Join Date: Jul 2006
Location: RI
Posts: 1,758
Default

Air leak?

Have you cleaned the carb?
__________________
2004 GasGas DE250
Reply With Quote
  #3  
Old 02-19-2009, 07:33 AM
jasont1532 jasont1532 is offline
Member
 
Join Date: Jan 2009
Location: stockholm,nj
Posts: 38
Default

the carb shouldnt be dirty, it is brand new, first tank of gas. also the rpm goes right back to idle after you crack/rev the throttle
__________________
05 ec300
01 wr426
98 polaris trail boss
Reply With Quote
  #4  
Old 02-19-2009, 08:34 AM
eff's Avatar
eff eff is offline
Silver Level Site Supporter
 
Join Date: Jul 2006
Location: RI
Posts: 1,758
Default

Check your cable routing. Many of us have replaced the stock cable with a cable that is 1.5" longer to avoid the throttle from being opened when turning the bars. If the stock cable isn't routed just right it can cause issues.
__________________
2004 GasGas DE250
Reply With Quote
  #5  
Old 02-19-2009, 08:45 AM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,601
Default

Could just be lean jetting considering the weather, you can richen the pilot and/or airscrew which should eliminate the hanging idle if it is a mixture problem.

Other than that, check the cable installation in the slide, and particularly the plastic spring guide to be sure its completely seated with the small tab in the notch of the cable anchor.

I'd get a longer cable, and also split your carb vents running a pair up to the airbox.

Are you Andy's friend that just got the GG?
Reply With Quote
  #6  
Old 02-19-2009, 10:25 AM
jasont1532 jasont1532 is offline
Member
 
Join Date: Jan 2009
Location: stockholm,nj
Posts: 38
Default

thanks guys i will ck. yes i am andy's friend. this is my first gas gas.
__________________
05 ec300
01 wr426
98 polaris trail boss
Reply With Quote
  #7  
Old 02-21-2009, 06:55 PM
jasont1532 jasont1532 is offline
Member
 
Join Date: Jan 2009
Location: stockholm,nj
Posts: 38
Default

pulled carb apart found main jet laying in bowl drain. guess that may be it. needle was at clip pos 2, set at pos 3. 40 pilot seems good,180 main #7 slide
__________________
05 ec300
01 wr426
98 polaris trail boss
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
ec250 stuck in gear thelonius General Discussions & Announcements 22 01-10-2010 01:09 PM
Powervalve Stuck? Dunk Enduro Engine - 2 stroke 3 07-22-2009 08:39 PM
Revs from hell -- stuck throttle or bad mojo? AZRickD Enduro Intake/Carburetion - 2 stroke 25 01-21-2009 08:54 PM
stuck between a ec250/300 blitzem General Discussions & Announcements 9 10-03-2008 10:40 PM
Stuck Throttle? jeffd Pictures & Videos 7 01-24-2007 08:04 AM




All times are GMT -5. The time now is 03:02 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org